EUVIMEDEUVIMED entdecken
Randomisierte kontrollierte StudieVergleichsstudieOpen Access · CC BY 4.0

Linear bone gain and healing complication rate comparative outcomes following ridge augmentation with custom 3D printed titanium mesh vs Ti-reinforced dPTFE. A randomized clinical trial

Krikor Giragosyan iD, Ivan Chenchev iD, Vasilena Ivanova iD

Folia Medica · 31.08.2024 · 66 (4) · 505-514

DOI: 10.3897/folmed.66.e123766 ↗

Kurz gefasst

Randomisierte kontrollierte Studie in der Zeitschrift Folia Medica, online erschienen am 31.08.2024. Verfasst von Krikor Giragosyan und 2 weiteren Autor:innen. Beteiligte Einrichtung: Medical University of Plovdiv, Plovdiv, Bulgaria. Hauptthemen laut MEDLINE: Titanium, Alveolar Ridge Augmentation, Printing, Three-Dimensional, Surgical Mesh. Die Arbeit wurde bisher 10-mal zitiert (Crossref) und nennt 25 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Aim

The aim of this randomized clinical trial was to compare the qualitative (linear alveolar ridge changes) and quantitative (healing complications) outcomes after guided bone regeneration (GBR) using a custom-made 3D printed titanium mesh versus titanium reinforced dense PTFE membrane for vertical and horizontal augmentation of deficient alveolar ridges. Materials and methods : Forty patients (40 defect sites) were included in the analysis. The patients were divided into two groups – a test group that received custom made Ti mesh and a control group which received a titanium reinforced dense polytetrafluoroethylene membrane. This case series documented consecutive patients treated with vertical bone augmentation to facilitate the future placement of dental implants. The procedure was performed using xenograft and autograft in a ratio of 1:1. Baseline vertical and horizontal deficiencies, acquired bone height and width as well as absolute bone gain (height and width) were recorded radiographically; postoperative complication rate was recorded clinically.

Results

The absolute bone height acquired for the test group was 3.65±1.73 mm, and for the control group - 4.24±2.19 mm; the absolute bone width acquired for the test group was 2.48±1.03 mm and for the control group - 2.60±0.82 mm. Postop complication rate was 33.3% for the test group and 38.9% for the control group.

Conclusion

The use of a custom-made 3D printed titanium mesh for needs of vertical and horizontal guided bone regeneration showed results comparable to those of – Ti d-PTFE both in terms of height and width gain and complication rate.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

TitaniumAlveolar Ridge AugmentationPrinting, Three-DimensionalSurgical MeshPolytetrafluoroethyleneHumansMaleFemaleMiddle AgedAdultBone RegenerationWound HealingGuided Tissue Regeneration, PeriodontalTreatment Outcome

Stichwörter der Autor:innen

bone grafts vertical ridge augmentation titanium mesh

Substanzen

TitaniumPolytetrafluoroethylene

Autor:innen und Institutionen

  • Medical University of Plovdiv, Plovdiv, Bulgaria.

ORCID-Profile: Krikor Giragosyan, Ivan Chenchev, Vasilena Ivanova

Zitieren

APA

Giragosyan, K., Chenchev, I., & Ivanova, V. (2024). Linear bone gain and healing complication rate comparative outcomes following ridge augmentation with custom 3D printed titanium mesh vs Ti-reinforced dPTFE. A randomized clinical trial. Folia Medica, 66(4), 505-514. https://doi.org/10.3897/folmed.66.e123766

Vancouver

Giragosyan K, Chenchev I, Ivanova V. Linear bone gain and healing complication rate comparative outcomes following ridge augmentation with custom 3D printed titanium mesh vs Ti-reinforced dPTFE. A randomized clinical trial. Folia Medica. 2024;66(4):505-514. doi:10.3897/folmed.66.e123766

BibTeX
@article{Giragosyan2024,
  author = {Giragosyan, Krikor and Chenchev, Ivan and Ivanova, Vasilena},
  title = {Linear bone gain and healing complication rate comparative outcomes following ridge augmentation with custom 3D printed titanium mesh vs Ti-reinforced dPTFE. A randomized clinical trial},
  journal = {Folia Medica},
  year = {2024},
  volume = {66},
  number = {4},
  pages = {505--514},
  doi = {10.3897/folmed.66.e123766}
}
Kostenlos starten →