EUVIMEDEUVIMED entdecken
Crossref

Assessment of the application of a novel three‐dimension printing individualized titanium mesh in alveolar bone augmentation: A retrospective study

Chang Liu iD, Jinmeng Li, Shuo Zhang iD, Hanyu Xiao, Yanying Wang, Jian Zhang

Clinical Implant Dentistry and Related Research · 2024-12 · 26 (6) · 1111-1125

DOI: 10.1111/cid.13372 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Clinical Implant Dentistry and Related Research, online erschienen am 12.08.2024. Verfasst von Chang Liu und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Oral Implantology, Tianjin Stomatological Hospital, Tianjin Stomatological Hospital, School of Medicine, Nankai University & Tianjin Ke…. Hauptthemen laut MEDLINE: Alveolar Ridge Augmentation, Titanium, Cone-Beam Computed Tomography, Printing, Three-Dimensional. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 55 Literaturangaben. Gefördert von: Tianjin Key Medical Discipline (Specialty) Construction Project, Tianjin Natural Science Foundation Multi-Investment Project for Youths, Tianjin Health Research Project.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objective

To assess the clinical and radiographic outcomes of alveolar ridge augmentation using a novel three‐dimensional printed individualized titanium mesh (3D‐PITM) for guided bone regeneration (GBR). Materials and methods Preoperative cone‐beam computed tomography (CBCT) was used to evaluate alveolar ridge defects, followed by augmentation with high‐porosity 3D‐PITM featuring circular and spindle‐shaped pores. Postoperative CBCT scans were taken immediately and after 6 months of healing. These scans were compared with preoperative scans to calculate changes in bone volume, height, and width, along with the corresponding resorption rates. A statistical analysis of the results was then conducted.

Results

A total of 21 patients participated in the study, involving alveolar ridge augmentation at 38 implant sites. After 6 months of healing, the average bone augmentation volume of 21 patients remained at 489.71 ± 252.53 mm 3 , with a resorption rate of 16.05% ± 8.07%. For 38 implant sites, the average vertical bone increment was 3.63 ± 2.29 mm, with a resorption rate of 17.55% ± 15.10%. The horizontal bone increment at the designed implant platform was 4.43 ± 1.85 mm, with a resorption rate of 25.26% ± 15.73%. The horizontal bone increment 2 mm below the platform was 5.50 ± 2.48 mm, with a resorption rate of 16.03% ± 9.57%. The main complication was exposure to 3D‐PITM, which occurred at a rate of 15.79%.

Conclusion

The novel 3D‐PITM used in GBR resulted in predictable bone augmentation. Moderate over‐augmentation in the design, proper soft tissue management, and rigorous follow‐ups are beneficial for reducing the graft resorption and the incidence of exposure.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Alveolar Ridge AugmentationTitaniumCone-Beam Computed TomographyPrinting, Three-DimensionalSurgical MeshHumansRetrospective StudiesFemaleMaleMiddle AgedAdultAlveolar Bone LossAgedBone RegenerationDental Implantation, EndosseousGuided Tissue Regeneration, Periodontal

Stichwörter der Autor:innen

3D‐printing individualized titanium meshalveolar ridge augmentationbone defectbone resorptionguided bone regenerationoral surgery procedures

Substanzen

Titanium

Autor:innen und Institutionen

  • Department of Oral Implantology, Tianjin Stomatological Hospital, Tianjin Stomatological Hospital, School of Medicine, Nankai University & Tianjin Key Laboratory of Oral and Maxillofacial Function Reconstruction, Tianji…

ORCID-Profile: Chang Liu, Shuo Zhang

Förderung

  • Tianjin Key Medical Discipline (Specialty) Construction Project
  • Tianjin Natural Science Foundation Multi-Investment Project for Youths
  • Tianjin Health Research Project

Zitieren

APA

Liu, C., Li, J., Zhang, S., Xiao, H., Wang, Y., & Zhang, J. (2024). Assessment of the application of a novel three‐dimension printing individualized titanium mesh in alveolar bone augmentation: A retrospective study. Clinical Implant Dentistry and Related Research, 26(6), 1111-1125. https://doi.org/10.1111/cid.13372

Vancouver

Liu C, Li J, Zhang S, Xiao H, Wang Y, Zhang J. Assessment of the application of a novel three‐dimension printing individualized titanium mesh in alveolar bone augmentation: A retrospective study. Clinical Implant Dentistry and Related Research. 2024;26(6):1111-1125. doi:10.1111/cid.13372

BibTeX
@article{Liu2024,
  author = {Liu, Chang and Li, Jinmeng and Zhang, Shuo and Xiao, Hanyu and Wang, Yanying and Zhang, Jian},
  title = {Assessment of the application of a novel three‐dimension printing individualized titanium mesh in alveolar bone augmentation: A retrospective study},
  journal = {Clinical Implant Dentistry and Related Research},
  year = {2024},
  volume = {26},
  number = {6},
  pages = {1111--1125},
  doi = {10.1111/cid.13372}
}
Kostenlos starten →