EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Design, Fabrication, and Structural Validation of a Formula Student Front Wing: A Vacuum-Assisted Hand Layup Case Study

Mina Youssef, Yomna Abdelaal, Veronika Sameh, Mostafa El-Tohamy, Jana Hussein, Omar Hussien, Mohamed Serry, Omar Abdelaziz

Vehicles · 19.11.2026 · 8 (11) · 305

DOI: 10.3390/vehicles8110305 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Vehicles, online erschienen am 19.11.2026. Verfasst von Mina Youssef und 7 weiteren Autor:innen. Die Arbeit nennt 64 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: American University in Cairo.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This paper presents an integrated design, manufacturing, and validation methodology for aerodynamic components, demonstrated on a Formula Student front wing built within a USD 192 budget. A Computational Fluid Dynamics (CFD) workflow, validated against measured forces on a double-element wing in ground effect within 3% in downforce, was applied in a target-driven sequence: a four-parameter two-element configuration reached approximately 166 N in 3D, below the 260 N target, motivating a seven-parameter, 600-point Design of Experiments for a three-element configuration. The final design predicted 270.0 N of downforce and 25.7 N of drag, with a 40.7:59.3 front-to-rear vehicle split against the 40:60 target. A scaled wind tunnel test confirmed the drag level only qualitatively, owing to Reynolds-number and ground-effect mismatch. Finite Element Method (FEM) analysis confirmed compliance with the Formula SAE (FSAE) deflection rule T8.3.1. A decision matrix selected 162 g/m2 twill glass fibre, wet-laid with epoxy over an expanded polystyrene core and vacuum-consolidated at about 0.8 bar below atmospheric on a fume-hood vacuum line, as the available pump could run for only 15 min. The largest airfoil of the 8.5 kg wing deflected 3.25 mm under the 200 N regulatory load, well within the 10 mm limit. The workflow provides a reproducible, low-cost route from vehicle-level targets to a physically verified component.

Förderung

  • American University in Cairo

Zitieren

APA

Youssef, M., Abdelaal, Y., Sameh, V., El-Tohamy, M., Hussein, J., Hussien, O., Serry, M., & Abdelaziz, O. (2026). Design, Fabrication, and Structural Validation of a Formula Student Front Wing: A Vacuum-Assisted Hand Layup Case Study. Vehicles, 8(11), 305. https://doi.org/10.3390/vehicles8110305

Vancouver

Youssef M, Abdelaal Y, Sameh V, El-Tohamy M, Hussein J, Hussien O, et al. Design, Fabrication, and Structural Validation of a Formula Student Front Wing: A Vacuum-Assisted Hand Layup Case Study. Vehicles. 2026;8(11):305. doi:10.3390/vehicles8110305

BibTeX
@article{Youssef2026,
  author = {Youssef, Mina and Abdelaal, Yomna and Sameh, Veronika and El-Tohamy, Mostafa and Hussein, Jana and Hussien, Omar and Serry, Mohamed and Abdelaziz, Omar},
  title = {Design, Fabrication, and Structural Validation of a Formula Student Front Wing: A Vacuum-Assisted Hand Layup Case Study},
  journal = {Vehicles},
  year = {2026},
  volume = {8},
  number = {11},
  pages = {305},
  doi = {10.3390/vehicles8110305}
}
Kostenlos starten →