EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Experimental and Statistical Evaluation of Infill Density Effects on the Mechanical Properties of FDM-Printed PLA, ABS, PC, and PETG Engineering Materials

Dilşad Akgümüş iD

Polymers · 17.08.2026 · 18 (16) · 1998

DOI: 10.3390/polym18161998 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 17.08.2026. Verfasst von Dilşad Akgümüş. Beteiligte Einrichtung: Engineering Faculty, Department of Mechanical Engineering, Istanbul Aydin University, 34295 Istanbul, Turkey. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 20 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Additive manufacturing (AM) has become prominent among advanced manufacturing technologies in recent years due to the advantages it offers in design flexibility, low material waste, and digitalization of the manufacturing process in cases where complex geometries are difficult or costly to produce with traditional methods. Fused deposition modeling (FDM) technology, which is based on the modeling of thermoplastic polymers by melting them layer by layer in a controlled manner, has become widespread in both industrial and academic applications due to its simplicity of process, low equipment cost, wide material compatibility, and sustainable manufacturing approach, and is effectively used in many areas from rapid prototyping to functional final products. In this study, the mechanical performances of different engineering polymers (ABS, PC, PLA, and PETG) produced with the FDM method at 30% and 60% infill densities were evaluated comparatively. The produced specimens were subjected to tensile, Charpy impact, hardness, and SEM analyses; structural strength and microstructure properties of the materials were examined. The results revealed that each material exhibited unique mechanical properties suitable for different applications. ABS was found suitable for applications requiring energy absorption with its superior impact absorption capacity and ductility. PC attracted attention with its highest strength and rigidity values, indicating that it can be preferred in structural parts where mechanical strength is critical. While PLA, one of the sustainable materials, stands out for biomedical components with its high ductility and flexibility properties, PETG provides advantages for carrier structures thanks to its better impact resistance and dimensional stability. The findings reveal that FDM technology can optimize mechanical properties through parameters such as material type and infill density, thereby providing a useful basis for material selection and design optimization in engineering applications.

Schlagwörter

Stichwörter der Autor:innen

additive manufacturingfused deposition modelinginfill densitythermoplastic polymer

Autor:innen und Institutionen

  • Engineering Faculty, Department of Mechanical Engineering, Istanbul Aydin University, 34295 Istanbul, Turkey.

ORCID-Profile: Dilşad Akgümüş

Zitieren

APA

Akgümüş, D. (2026). Experimental and Statistical Evaluation of Infill Density Effects on the Mechanical Properties of FDM-Printed PLA, ABS, PC, and PETG Engineering Materials. Polymers, 18(16), 1998. https://doi.org/10.3390/polym18161998

Vancouver

Akgümüş D. Experimental and Statistical Evaluation of Infill Density Effects on the Mechanical Properties of FDM-Printed PLA, ABS, PC, and PETG Engineering Materials. Polymers. 2026;18(16):1998. doi:10.3390/polym18161998

BibTeX
@article{Akgm2026,
  author = {Akgümüş, Dilşad},
  title = {Experimental and Statistical Evaluation of Infill Density Effects on the Mechanical Properties of FDM-Printed PLA, ABS, PC, and PETG Engineering Materials},
  journal = {Polymers},
  year = {2026},
  volume = {18},
  number = {16},
  pages = {1998},
  doi = {10.3390/polym18161998}
}
Kostenlos starten →