Mechanical Performance of FDM-Printed PLA Joined by Portable Friction Stir Welding: Influence of Infill Density and Tool Pin Geometry
Polymers · 22.04.2026 · 18 (9) · 1013
DOI: 10.3390/polym18091013 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 22.04.2026. Verfasst von Juan Antonio Almazán und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical and Mining Engineering, A3 Building-Campus Las Lagunillas, University of Jaen, s/n, 23071 Jaen, Spain. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 54 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).
Abstract (Originalsprache)
This study evaluates the mechanical performance of FDM-printed poly(lactic acid) (PLA) structures joined using a portable Friction Stir Welding (FSW) device. A non-destructive optical band method was employed to assess weld homogeneity and material flow consistency. The influence of substrate infill density (15% and 100%) and tool pin geometry (cylindrical and truncated conical) was systematically analyzed. Results indicate that substrate density is the primary determinant of joint integrity; 100% infill specimens demonstrated superior structural homogeneity and consistent intensity profiles, whereas 15% infill specimens exhibited significant intensity fluctuations and poor consolidation, even with the addition of filler material. The mechanical evaluation revealed that the use of a tool pin is essential for effective load transfer, as specimens welded without internal agitation achieved only baseline tensile strengths of approximately 4 MPa. Among the pin-driven configurations, the cylindrical geometry outperformed the truncated conical design, reaching a peak tensile stress of 8.02 ± 1.42 MPa, corresponding to a joint efficiency of 27% relative to the 100% infill base material, compared to 6.25 ± 1.43 MPa. This performance gap is attributed to the cylindrical pin’s ability to maintain higher shear rates and more uniform pressure distribution at the weld root. These findings demonstrate the feasibility of portable FSW for structural joining of additively manufactured polymers and establish critical processing parameters for the optimization of portable FSW in engineering applications.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Mechanical and Mining Engineering, A3 Building-Campus Las Lagunillas, University of Jaen, s/n, 23071 Jaen, Spain.
- Teaching and Research Laboratories of the Central Research Support Services (SCAI), A2 Building-Campus Las Lagunillas, University of Jaen, s/n, 23071 Jaen, Spain.
- Department of Manufacturing Engineering, Industrial Engineering School, Universidad Nacional de Educación a Distancia (UNED), St/Juan del Rosal 12, 28040 Madrid, Spain.
ORCID-Profile: Juan Antonio Almazán, Marta M Marín, Amabel García-Domínguez, Eva María Rubio
Zitieren
APA
Almazán, J. A., Almazán, M. Á., Marín, M. M., García-Domínguez, A., & Rubio, E. M. (2026). Mechanical Performance of FDM-Printed PLA Joined by Portable Friction Stir Welding: Influence of Infill Density and Tool Pin Geometry. Polymers, 18(9), 1013. https://doi.org/10.3390/polym18091013
Vancouver
Almazán JA, Almazán MÁ, Marín MM, García-Domínguez A, Rubio EM. Mechanical Performance of FDM-Printed PLA Joined by Portable Friction Stir Welding: Influence of Infill Density and Tool Pin Geometry. Polymers. 2026;18(9):1013. doi:10.3390/polym18091013
BibTeX
@article{Almazn2026,
author = {Almazán, Juan Antonio and Almazán, Miguel Ángel and Marín, Marta M and García-Domínguez, Amabel and Rubio, Eva María},
title = {Mechanical Performance of FDM-Printed PLA Joined by Portable Friction Stir Welding: Influence of Infill Density and Tool Pin Geometry},
journal = {Polymers},
year = {2026},
volume = {18},
number = {9},
pages = {1013},
doi = {10.3390/polym18091013}
}
EUVIMED