EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Structure–Property Relationships of Hot-Pressed Wood–Polymer Composite Boards from Recycled ABS Edge-Banding Waste and Wood Fibers

Viktor Savov iD, Petar Antov iD, Alexandrina Kostadinova-Slaveva iD, Ekaterina Todorova iD, Matei Botev, Georgi Ivanov, Viktoria Dudeva iD, Martina Todorova iD, Konstantinos Ninikas iD, Stoyko Petrin iD, Anton Kuzmin iD

Polymers · 26.06.2026 · 18 (13) · 1591

DOI: 10.3390/polym18131591 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 26.06.2026. Verfasst von Viktor Savov und 10 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Forest Industry, University of Forestry, 1797 Sofia, Bulgaria. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 42 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: European Union.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Recycled thermoplastics offer a promising route for valorizing industrial residues and developing thermoplastic-bonded wood-based panels without added formaldehyde-based resins. In this study, experimental wood–polymer composite boards were produced from recycled acrylonitrile–butadiene–styrene (ABS) edge-banding waste used as the polymer matrix and industrial wood fibers used as the lignocellulosic reinforcement. The boards were manufactured at target densities of 800–1200 kg·m−3 and wood fiber contents of 10–30%, followed by the evaluation of selected physical and mechanical properties, including water absorption, thickness swelling, modulus of elasticity and bending strength. Thermogravimetric analysis of the recycled ABS edge-banding material and qualitative optical microscopy of the board surfaces were used to support, but not independently prove, the interpretation of the composite structure. The recycled ABS waste enabled the formation of compact boards, with density exerting the strongest influence on water resistance and bending performance. The regression models indicated a balanced region at 21.84 wt.% wood fibers and 1134 kg·m−3, corresponding to predicted water absorption of 1.62%, thickness swelling of 3.22%, modulus of elasticity of 2931 N·mm−2 and bending strength of 22.20 N·mm−2. Optical microscopy suggested a more continuous ABS-rich surface in the most homogeneous specimens, whereas local accumulations of fine particles and areas of limited polymer coverage were observed on the opposite surface. These findings demonstrate the potential of recycled ABS edge-banding waste for wood–polymer board production, while indicating that additional feedstock cleaning and sieving should be investigated in subsequent work to improve furnish uniformity and structural homogeneity.

Schlagwörter

Stichwörter der Autor:innen

composite boardsedge-banding wasterecycled ABSstructural homogeneitythermoplastic matrixwood fiberswood–polymer composites

Autor:innen und Institutionen

  • Faculty of Forest Industry, University of Forestry, 1797 Sofia, Bulgaria.
  • Center of Competence "Clean Technologies for a Sustainable Environment-Water, Waste, Energy for a Circular Economy", 1407 Sofia, Bulgaria.
  • Faculty of Ecology and Landscape Architecture, University of Forestry, 1797 Sofia, Bulgaria.
  • Department of Forestry, Wood Sciences & Design, School of Technology, University of Thessaly, 43100 Karditsa, Greece.
  • Faculty of Chemical Technologies, University of Chemical Technology and Metallurgy, 1757 Sofia, Bulgaria.
  • Laboratory of Advanced Composite Materials and Technologies, Federal State Budgetary Educational Institution of Higher Education, Plekhanov Russian University of Economics, 117997 Moscow, Russia.

ORCID-Profile: Viktor Savov, Petar Antov, Alexandrina Kostadinova-Slaveva, Ekaterina Todorova, Viktoria Dudeva, Martina Todorova, Konstantinos Ninikas, Stoyko Petrin, Anton Kuzmin

Förderung

  • European Union

Zitieren

APA

Savov, V., Antov, P., Kostadinova-Slaveva, A., Todorova, E., Botev, M., Ivanov, G., Dudeva, V., Todorova, M., Ninikas, K., Petrin, S., & Kuzmin, A. (2026). Structure–Property Relationships of Hot-Pressed Wood–Polymer Composite Boards from Recycled ABS Edge-Banding Waste and Wood Fibers. Polymers, 18(13), 1591. https://doi.org/10.3390/polym18131591

Vancouver

Savov V, Antov P, Kostadinova-Slaveva A, Todorova E, Botev M, Ivanov G, et al. Structure–Property Relationships of Hot-Pressed Wood–Polymer Composite Boards from Recycled ABS Edge-Banding Waste and Wood Fibers. Polymers. 2026;18(13):1591. doi:10.3390/polym18131591

BibTeX
@article{Savov2026,
  author = {Savov, Viktor and Antov, Petar and Kostadinova-Slaveva, Alexandrina and Todorova, Ekaterina and Botev, Matei and Ivanov, Georgi and Dudeva, Viktoria and Todorova, Martina and Ninikas, Konstantinos and Petrin, Stoyko and Kuzmin, Anton},
  title = {Structure–Property Relationships of Hot-Pressed Wood–Polymer Composite Boards from Recycled ABS Edge-Banding Waste and Wood Fibers},
  journal = {Polymers},
  year = {2026},
  volume = {18},
  number = {13},
  pages = {1591},
  doi = {10.3390/polym18131591}
}
Kostenlos starten →