EUVIMEDEUVIMED entdecken
ÜbersichtsarbeitSystematische ÜbersichtMetaanalyseOpen Access · CC BY 4.0

Mechanical Performance of CAD/CAM-Milled Versus 3D-Printed Resins for Prosthetic Applications: A Systematic Review and Meta-Analysis

Carlos Carpio-Cevallos iD, Luis Chauca-Bajaña iD, Andrea Ordoñez-Balladares iD, Benjamín José Martín-Biedma iD, Byron Velasquez Ron iD, José Martín-Cruces iD

Polymers · 21.05.2026 · 18 (10) · 1257

DOI: 10.3390/polym18101257 ↗

Kurz gefasst

Übersichtsarbeit in der Zeitschrift Polymers, online erschienen am 21.05.2026. Verfasst von Carlos Carpio-Cevallos und 5 weiteren Autor:innen. Beteiligte Einrichtung: Dental Sciences, College Dentistry, University of Guayaquil, Guayaquil 090514, Ecuador. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 42 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Background

Digital fabrication techniques such as CAD/CAM milling and 3D printing are widely used for provisional dental restorations. However, differences in mechanical performance remain controversial.

Objective

To compare the hardness and flexural strength of CAD/CAM-milled resins versus 3D-printed resins used in restorative dentistry.

Methods

A systematic review and meta-analysis were conducted following PRISMA 2020 guidelines and registered in PROSPERO (CRD420251045547). Electronic searches were performed in PubMed, Scopus, Web of Science, Embase, and LILACS. In vitro studies comparing CAD/CAM-milled and 3D-printed resins in terms of hardness and/or flexural strength were included. A random-effects inverse-variance model was applied using standardized mean difference (SMD) with 95% confidence intervals (CI). Risk of bias was assessed using the RoB-Iv tool.

Results

Four studies (n = 124 specimens) were included in the hardness meta-analysis. CAD/CAM-milled resins showed significantly higher hardness (SMD = 2.92; 95% CI: 0.34–5.49; p = 0.026), although heterogeneity was high (I2 = 94.9%). Funnel plot asymmetry suggested possible small-study effects. For flexural strength, three studies (n = 40 specimens) were analyzed, demonstrating a significant effect favoring milled resins (SMD = 1.28; 95% CI: 0.42–2.14; p = 0.0036) with low-to-moderate heterogeneity (I2 = 27.8%). Sensitivity analyses confirmed robustness for both outcomes. Overall methodological quality was acceptable, with no high risk of bias identified in strength studies.

Conclusions

CAD/CAM-milled resins tend to demonstrate higher hardness and flexural strength compared with 3D-printed resins. However, the substantial heterogeneity observed, particularly for hardness, and the potential influence of methodological variability, warrant cautious interpretation of these findings.

Schlagwörter

Stichwörter der Autor:innen

3Dcomputer-aided designcomputer-aided manufacturingdental materials

Autor:innen und Institutionen

  • Dental Sciences, College Dentistry, University of Guayaquil, Guayaquil 090514, Ecuador.
  • Universidade de Santiago de Compostela, Santiago de Compostela, 15705 A Coruña, Spain.
  • School of Dentistry, Universidad Católica de Santiago de Guayaquil (UCSG), Guayaquil 090101, Ecuador.
  • College Dentistry, Universidad Bolivariana del Ecuador, Durán 092406, Ecuador.
  • Oral Sciences Research Group, Endodontics and Restorative Dentistry Unit, School of Medicine and Dentistry, Universidade de Santiago de Compostela, Health Research Institute of Santiago (IDIS), Rúa Entrerríos 1, 15705 S…
  • Carrera de Odontología, Department Prosthesis Research, Universidad de Las Américas Ecuador (UDLA), Quito 170102, Ecuador.

ORCID-Profile: Carlos Carpio-Cevallos, Luis Chauca-Bajaña, Andrea Ordoñez-Balladares, Benjamín José Martín-Biedma, Byron Velasquez Ron, José Martín-Cruces

Zitieren

APA

Carpio-Cevallos, C., Chauca-Bajaña, L., Ordoñez-Balladares, A., Martín-Biedma, B. J., Velasquez Ron, B., & Martín-Cruces, J. (2026). Mechanical Performance of CAD/CAM-Milled Versus 3D-Printed Resins for Prosthetic Applications: A Systematic Review and Meta-Analysis. Polymers, 18(10), 1257. https://doi.org/10.3390/polym18101257

Vancouver

Carpio-Cevallos C, Chauca-Bajaña L, Ordoñez-Balladares A, Martín-Biedma BJ, Velasquez Ron B, Martín-Cruces J. Mechanical Performance of CAD/CAM-Milled Versus 3D-Printed Resins for Prosthetic Applications: A Systematic Review and Meta-Analysis. Polymers. 2026;18(10):1257. doi:10.3390/polym18101257

BibTeX
@article{CarpioCevallos2026,
  author = {Carpio-Cevallos, Carlos and Chauca-Bajaña, Luis and Ordoñez-Balladares, Andrea and Martín-Biedma, Benjamín José and Velasquez Ron, Byron and Martín-Cruces, José},
  title = {Mechanical Performance of CAD/CAM-Milled Versus 3D-Printed Resins for Prosthetic Applications: A Systematic Review and Meta-Analysis},
  journal = {Polymers},
  year = {2026},
  volume = {18},
  number = {10},
  pages = {1257},
  doi = {10.3390/polym18101257}
}
Kostenlos starten →