EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Laser-Based Polishing of Additively Manufactured PA12 and PAEK Polymer Components Using a Robotic System

Emrah Uluz iD, Leander Metz, Lukas Hedwig, Sebastian Bremen

Polymers · 30.04.2026 · 18 (9) · 1106

DOI: 10.3390/polym18091106 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 30.04.2026. Verfasst von Emrah Uluz und 3 weiteren Autor:innen. Beteiligte Einrichtung: Fraunhofer Institute for Laser Technology ILT, Steinbachstraße 15, 52074 Aachen, Germany. Die Arbeit nennt 22 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Deutsches Zentrum für Luft- und Raumfahrt e. V. (DLR), German Federal Ministry for Economic Affairs and Energy.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

A non-contact laser polishing method for additively manufactured polymer components with complex three-dimensional geometries is presented, employing a 6-axis robotic system. Robot-guided sample orientation, a quasi-top-hat scanning strategy, and closed-loop temperature control are combined to address curved geometries. On Selective Laser Sintering (SLS)-manufactured Polyamide 12 (PA12) tensile samples with three build orientations and two thicknesses, laser polishing yields up to a 15% increase in tensile strength (Rm) and a 50% increase in elongation at break (A). For 45°-built 5 mm samples, Rm increases from 31.53 MPa to 36.33 MPa and A from 6.52% to 9.8%, approaching the tensile strength reported for optimally oriented SLS-printed PA12 Smooth samples of the same grade. For convex–concave PA12 demonstrators, areal roughness (Sa) on convex surfaces is reduced from 33.6 µm to 2.7 µm (approximately 92%) and the high-pass-filtered micro-roughness (SaHP) on concave surfaces by 98.2% to 0.15 µm. For Fused Deposition Modeling (FDM)-printed Polyaryletherketone (PAEK) samples, Sa is reduced from 28.35 µm to 4.1 µm and SaHP from 15.98 µm to 0.23 µm (98.6%), despite the high melting temperature and anisotropic raster topography. These results demonstrate that robotic laser polishing constitutes a viable post-processing approach for functionally demanding polymer applications.

Schlagwörter

Stichwörter der Autor:innen

Polyamide 12Polyaryletherketoneadditive manufacturingfused deposition modelinglaser polishingmechanical propertiesselective laser sinteringsurface roughness

Autor:innen und Institutionen

  • Fraunhofer Institute for Laser Technology ILT, Steinbachstraße 15, 52074 Aachen, Germany.
  • Chair for Laser Technology LLT, RWTH Aachen University, Templergraben 55, 52062 Aachen, Germany.
  • Department of Mechanical Engineering and Mechatronics, FH Aachen University of Applied Sciences, Goethestraße 1, 52064 Aachen, Germany.

ORCID-Profile: Emrah Uluz

Förderung

  • Deutsches Zentrum für Luft- und Raumfahrt e. V. (DLR)
  • German Federal Ministry for Economic Affairs and Energy

Zitieren

APA

Uluz, E., Metz, L., Hedwig, L., & Bremen, S. (2026). Laser-Based Polishing of Additively Manufactured PA12 and PAEK Polymer Components Using a Robotic System. Polymers, 18(9), 1106. https://doi.org/10.3390/polym18091106

Vancouver

Uluz E, Metz L, Hedwig L, Bremen S. Laser-Based Polishing of Additively Manufactured PA12 and PAEK Polymer Components Using a Robotic System. Polymers. 2026;18(9):1106. doi:10.3390/polym18091106

BibTeX
@article{Uluz2026,
  author = {Uluz, Emrah and Metz, Leander and Hedwig, Lukas and Bremen, Sebastian},
  title = {Laser-Based Polishing of Additively Manufactured PA12 and PAEK Polymer Components Using a Robotic System},
  journal = {Polymers},
  year = {2026},
  volume = {18},
  number = {9},
  pages = {1106},
  doi = {10.3390/polym18091106}
}
Kostenlos starten →