EUVIMEDEUVIMED entdecken
Crossref

Laser Surface Polishing of Additively Manufactured Components Via Beam Shaping: Influence on Surface Topography, Microstructure, and Mechanical Properties

Bikram K. Khandai, Arkajyoti Jha, Shivam Shukla, Vignan Babu Dyavanapelly, Muvvala Gopinath

Journal of Manufacturing Science and Engineering · 01.08.2026 · 148 (8)

DOI: 10.1115/1.4072054 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Manufacturing Science and Engineering, online erschienen am 09.06.2026. Verfasst von Bikram K. Khandai und 4 weiteren Autor:innen. Die Arbeit nennt 32 Literaturangaben. Gefördert von: Defence Research and Development Organisation.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Additively manufactured components often exhibit poor surface quality due to partially fused powder particles and overlapping tracks. To overcome this limitation, laser surface polishing (LSP) was applied to laser-directed energy deposited Stellite6 samples. LSP involves surface remelting, redistributing molten material between peaks and valleys, and eliminating asperities formed during deposition. In this study, two beam geometries, a circular beam (3 mm diameter) and a line beam (16 × 0.5 mm2), were evaluated for improving surface finish and mechanical performance. A constant interaction time was maintained using polishing speeds of 1200 mm/min for the circular beam and 200 mm/min for the line beam at 1000 W. Scanning orientations of 0 deg, 45 deg, and 90 deg relative to deposition tracks were investigated. The line beam at 0 deg produced the best surface finish by melting tracks simultaneously, whereas the circular beam melted fewer tracks per pass. At 90 deg, the narrow line beam limited effectiveness, and at 45 deg, both beams produced poor finish due to misaligned melt pools. Surface roughness reductions of ∼80% and ∼86% were achieved with the circular and line beams. Both beams enhanced hardness and wear resistance through microstructural refinement. The circular beam caused deeper remelting with a columnar dendritic structure, while the line beam produced a shallower melt pool with equiaxed grains. Wear changed from adhesive in as-deposited samples to abrasive and delamination after polishing, with circular beam-treated samples showing the least wear. Overall, LSP improved surface quality and mechanical performance, with beam geometry and scan orientation influencing outcomes.

Förderung

  • Defence Research and Development Organisation

Zitieren

APA

Khandai, B. K., Jha, A., Shukla, S., Dyavanapelly, V. B., & Gopinath, M. (2026). Laser Surface Polishing of Additively Manufactured Components Via Beam Shaping: Influence on Surface Topography, Microstructure, and Mechanical Properties. Journal of Manufacturing Science and Engineering, 148(8). https://doi.org/10.1115/1.4072054

Vancouver

Khandai BK, Jha A, Shukla S, Dyavanapelly VB, Gopinath M. Laser Surface Polishing of Additively Manufactured Components Via Beam Shaping: Influence on Surface Topography, Microstructure, and Mechanical Properties. Journal of Manufacturing Science and Engineering. 2026;148(8). doi:10.1115/1.4072054

BibTeX
@article{Khandai2026,
  author = {Khandai, Bikram K. and Jha, Arkajyoti and Shukla, Shivam and Dyavanapelly, Vignan Babu and Gopinath, Muvvala},
  title = {Laser Surface Polishing of Additively Manufactured Components Via Beam Shaping: Influence on Surface Topography, Microstructure, and Mechanical Properties},
  journal = {Journal of Manufacturing Science and Engineering},
  year = {2026},
  volume = {148},
  number = {8},
  doi = {10.1115/1.4072054}
}
Kostenlos starten →