Enabling Industrial Re-Use of Large-Format Additive Manufacturing Molding and Tooling
Polymers · 10.11.2025 · 17 (22) · 2981
DOI: 10.3390/polym17222981 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 10.11.2025. Verfasst von Matthew Korey und 13 weiteren Autor:innen. Beteiligte Einrichtung: Oak Ridge National Laboratory, Manufacturing Science Division, 1 Bethel Valley Rd., Oak Ridge, TN 37830, USA. Die Arbeit wurde bisher 8-mal zitiert (Crossref) und nennt 46 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: United States Department of Energy, Oak Ridge National Laboratory.
Abstract (Originalsprache)
Large-format additive manufacturing (LFAM) is an enabling manufacturing technology capable of producing large parts with highly complex geometries for a wide variety of applications, including automotive, infrastructure/construction, and aerospace mold and tooling. In the past decade, the LFAM industry has seen widespread use of bio-based, glass, and/or carbon fiber reinforced thermoplastic composites which, when printed, serve as a lower-cost alternative to metallic parts. One of the highest-volume materials utilized by the industry is carbon fiber (CF)-filled polycarbonate (PC), which in out-of-autoclave applications can achieve comparable mechanical performance to metal at a significantly lower cost. Previous work has shown that if this material is recovered at various points throughout the manufacturing process for both the lab and pilot scale, it can be mechanically recycled with minimal impacts on the functional performance and printability of the material while significantly reducing the feedstock costs. End-of-life (EOL) CF-PC components were processed through industrial shredding, melt compounding, and LFAM equipment, followed by evaluation of the second-life material properties. Experimental assessments included quantitative analysis of fiber length attrition, polymer molecular weight degradation using gel permeation chromatography (GPC), density changes via pycnometry, thermal performance using dynamic mechanical analysis (DMA), and mechanical performance (tensile properties) in both the X- and Z-directions. Results demonstrated a 24.6% reduction in average fiber length compared to virgin prints, accompanied by a 21% decrease in X-direction tensile strength and a 39% reduction in tensile modulus. Despite these reductions, Z-direction tensile modulus improved by 4%, density increased by 6.8%, and heat deflection temperature (HDT) under high stress retained over 97% of its original value. These findings underscore the potential for integrating mechanically recycled CF-PC into industrial LFAM applications while highlighting the need for technological innovations to mitigate fiber degradation and enhance material performance for broader adoption. This critical step toward circular material practices in LFAM offers a pathway to reducing feedstock costs and environmental impact while maintaining functional performance in industrial applications.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Oak Ridge National Laboratory, Manufacturing Science Division, 1 Bethel Valley Rd., Oak Ridge, TN 37830, USA.
- Department of Mechanical & Aerospace Engineering, University of Tennessee Knoxville, 400 W. Summit Hill Dr., Knoxville, TN 37902, USA.
- Airtech International Inc., 5700 Skylab Road, Huntington Beach, CA 92647, USA.
- Department of Materials Science & Engineering, University of Tennessee Knoxville, 400 W. Summit Hill Dr., Knoxville, TN 37902, USA.
- ORISE Participant in the U.S. Department of Energy Education Collaboration at ORNL Program, 1299 Bethel Valley Rd., Oak Ridge, TN 37830, USA.
- ORISE Participant in the U.S. Department of Energy Science Undergraduate Laboratory Internships Program, 1299 Bethel Valley Rd., Oak Ridge, TN 37830, USA.
ORCID-Profile: Matthew Korey, Kathryn Slavny, Katie Copenhaver, Tyler Corum, William M Gramlich
Förderung
- United States Department of Energy
- Oak Ridge National Laboratory
Zitieren
APA
Korey, M., Hubbard, A. M., Haye, G., Bedsole, R., Skelton, Z., Meshkat, N., Anilal, A. L. S., Slavny, K., Copenhaver, K., Corum, T., Bones, D. X., Gramlich, W. M., Duty, C., & Ozcan, S. (2025). Enabling Industrial Re-Use of Large-Format Additive Manufacturing Molding and Tooling. Polymers, 17(22), 2981. https://doi.org/10.3390/polym17222981
Vancouver
Korey M, Hubbard AM, Haye G, Bedsole R, Skelton Z, Meshkat N, et al. Enabling Industrial Re-Use of Large-Format Additive Manufacturing Molding and Tooling. Polymers. 2025;17(22):2981. doi:10.3390/polym17222981
BibTeX
@article{Korey2025,
author = {Korey, Matthew and Hubbard, Amber M and Haye, Gregory and Bedsole, Robert and Skelton, Zachary and Meshkat, Neeki and Anilal, Ashish L S and Slavny, Kathryn and Copenhaver, Katie and Corum, Tyler and Bones, Don X and Gramlich, William M and Duty, Chad and Ozcan, Soydan},
title = {Enabling Industrial Re-Use of Large-Format Additive Manufacturing Molding and Tooling},
journal = {Polymers},
year = {2025},
volume = {17},
number = {22},
pages = {2981},
doi = {10.3390/polym17222981}
}
EUVIMED