EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Drilling Surface Quality Analysis of Carbon Fiber-Reinforced Polymers Based on Acoustic Emission Characteristics

Mengke Yan, Yushu Lai, Yiwei Zhang, Lin Yang, Yan Zheng, Tianlong Wen, Cunxi Pan

Polymers · 28.09.2025 · 17 (19) · 2628

DOI: 10.3390/polym17192628 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 28.09.2025. Verfasst von Mengke Yan und 6 weiteren Autor:innen. Beteiligte Einrichtung: Chongqing Engineering Research Center for Advanced Intelligent Manufacturing Technology, Chongqing Three Gorges University, Chongqing 404000, China. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 38 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: the Scientific and technological research project of Chongqing Municipal Education Commission, the Research Institute of Intelligent Manufacturing Industry Technology of SiChuan Arts and Science university, the General Project of Natural Science Foundation of Chongqing.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

CFRP is extensively utilized in the manufacturing of aerospace equipment owing to its distinctive properties, and hole-making processing continues to be the predominant processing method for this material. However, due to the anisotropy of CFRP, in its processing process, processing damage appears easily, such as stratification, fiber tearing, burrs, etc. These damages will seriously affect the performance of CFRP components in the service process. This work employs acoustic emission (AE) and infrared thermography (IT) techniques to analyze the characteristics of AE signals and temperature signals generated during the CFRP drilling process. Fast Fourier transform (FFT) and short-time Fourier transform (STFT) are used to process the collected AE signals. And in combination with the actual damage morphology, the material removal behavior during the drilling process and the AE signal characteristics corresponding to processing defects are studied. The results show that the time-frequency graph and root mean square (RMS) curve of the AE signal can accurately distinguish the different stages of the drilling process. Through the analysis of the frequency domain characteristics of the AE signal, the specific frequency range of the damage mode of the CFRP composite material during drilling is determined. This paper aims to demonstrate the feasibility of real-time monitoring of the drilling process. By analyzing the relationship between the RMS values of acoustic emission signals and hole surface topography under different drilling parameters, it provides a new approach for the research on online monitoring of CFRP drilling damage and improvement of CFRP machining quality.

Schlagwörter

Stichwörter der Autor:innen

acoustic emissioncarbon fiber-reinforced polymer (CFRP)damage identificationdrillingsignal processing

Autor:innen und Institutionen

  • Chongqing Engineering Research Center for Advanced Intelligent Manufacturing Technology, Chongqing Three Gorges University, Chongqing 404000, China.
  • Chongqing Engineering Technology Research Center for Light Alloy and Processing, Chongqing Three Gorges University, Chongqing 404000, China.
  • Intelligent Manufacturing Industry Technology Research Institute, SiChuan Arts and Science University, Dazhou 635000, China.
  • School of Mechatronic Engineering, Southwest Petroleum University, Chengdu 610500, China.

Förderung

  • the Scientific and technological research project of Chongqing Municipal Education Commission
  • the Research Institute of Intelligent Manufacturing Industry Technology of SiChuan Arts and Science university
  • the General Project of Natural Science Foundation of Chongqing
  • General Project of Natural Science Foundation of Chongqing
  • Scientific and technological research project of Chongqing Municipal Education Commission
  • Research Institute of Intelligent Manufacturing Industry Technology of SiChuan Arts and Science university

Zitieren

APA

Yan, M., Lai, Y., Zhang, Y., Yang, L., Zheng, Y., Wen, T., & Pan, C. (2025). Drilling Surface Quality Analysis of Carbon Fiber-Reinforced Polymers Based on Acoustic Emission Characteristics. Polymers, 17(19), 2628. https://doi.org/10.3390/polym17192628

Vancouver

Yan M, Lai Y, Zhang Y, Yang L, Zheng Y, Wen T, et al. Drilling Surface Quality Analysis of Carbon Fiber-Reinforced Polymers Based on Acoustic Emission Characteristics. Polymers. 2025;17(19):2628. doi:10.3390/polym17192628

BibTeX
@article{Yan2025,
  author = {Yan, Mengke and Lai, Yushu and Zhang, Yiwei and Yang, Lin and Zheng, Yan and Wen, Tianlong and Pan, Cunxi},
  title = {Drilling Surface Quality Analysis of Carbon Fiber-Reinforced Polymers Based on Acoustic Emission Characteristics},
  journal = {Polymers},
  year = {2025},
  volume = {17},
  number = {19},
  pages = {2628},
  doi = {10.3390/polym17192628}
}
Kostenlos starten →