EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Waste Coffee Silver Skin as a Natural Filler in PLA-Based Filaments for Fused Filament Fabrication (FFF) Printing

Ana C Machado iD, Ana F Costa, Ângela R Rodrigues, Pedro F Moreira iD, Fernando M Duarte iD, António J Pontes iD

Polymers · 26.06.2025 · 17 (13) · 1766

DOI: 10.3390/polym17131766 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 26.06.2025. Verfasst von Ana C Machado und 5 weiteren Autor:innen. Beteiligte Einrichtung: IPC-Institute for Polymers and Composites, University of Minho, 4800-058 Guimarães, Portugal. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 54 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: RRP - Recovery and Resilience Plan and by the European Funds NextGeneration EU. http://www.recuperarportugal.gov.pt/, Agendas para a Inovação Empresarial, RRP-Recovery and Resilience Plan.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In this research, novel biocomposite filaments were developed by incorporating coffee silver skin (CSS) waste into polylactic acid (PLA) for use in Fused Filament Fabrication (FFF) technology. CSS was blended with PLA at concentrations of 0, 5, 10, and 15 wt.% to address the waste disposal challenge and produce environmentally friendly composite biofilaments for FFF, supporting circular economic efforts. These filaments have the potential to be used in sustainable prototyping, functional parts, and consumer products. A comprehensive analysis was conducted to examine the effect of printing temperature on dimensional accuracy, melt flow index (MFI), and mechanical properties. Higher printing temperatures and increased CSS content led to larger dimensions due to increased material fluidity, as confirmed by MFI results, which increased from 3.5 g/10 min (0% CSS) to 5.8 g/10 min (15% CSS) at 180 °C, reaching 26.3 g/10 min at 220 °C. Tensile tests on 3D-printed specimens indicated an improvement in elastic modulus with increasing CSS content at lower temperatures (180 °C), rising from 1622 MPa (0% CSS) to 1952 MPa (15% CSS), representing about a 20% increase. However, at higher temperatures, the elastic modulus decreased, possibly due to the poor dispersion and agglomeration of filler particles. Tensile strength generally decreased with CSS addition, especially at higher loadings, while yield elongation remained low (~1.4–1.7%), indicating a more brittle material. The findings also revealed no significant thermal changes with increasing CSS content, and good printability was achieved for all compositions, which was characterized by good layer adhesion, the absence of warping, and the ease of extrusion.

Schlagwörter

Stichwörter der Autor:innen

additive manufacturingbiobased materialscircular manufacturingsustainable compositewaste coffee silver skin

Autor:innen und Institutionen

  • IPC-Institute for Polymers and Composites, University of Minho, 4800-058 Guimarães, Portugal.
  • Done Lab-Advanced Manufacturing of Products and Tools, University of Minho, 4800-058 Guimarães, Portugal.

ORCID-Profile: Ana C Machado, Pedro F Moreira, Fernando M Duarte, António J Pontes

Förderung

  • RRP - Recovery and Resilience Plan and by the European Funds NextGeneration EU. http://www.recuperarportugal.gov.pt/
  • Agendas para a Inovação Empresarial
  • RRP-Recovery and Resilience Plan
  • European Funds NextGeneration EU

Zitieren

APA

Machado, A. C., Costa, A. F., Rodrigues, Â. R., Moreira, P. F., Duarte, F. M., & Pontes, A. J. (2025). Waste Coffee Silver Skin as a Natural Filler in PLA-Based Filaments for Fused Filament Fabrication (FFF) Printing. Polymers, 17(13), 1766. https://doi.org/10.3390/polym17131766

Vancouver

Machado AC, Costa AF, Rodrigues ÂR, Moreira PF, Duarte FM, Pontes AJ. Waste Coffee Silver Skin as a Natural Filler in PLA-Based Filaments for Fused Filament Fabrication (FFF) Printing. Polymers. 2025;17(13):1766. doi:10.3390/polym17131766

BibTeX
@article{Machado2025,
  author = {Machado, Ana C and Costa, Ana F and Rodrigues, Ângela R and Moreira, Pedro F and Duarte, Fernando M and Pontes, António J},
  title = {Waste Coffee Silver Skin as a Natural Filler in PLA-Based Filaments for Fused Filament Fabrication (FFF) Printing},
  journal = {Polymers},
  year = {2025},
  volume = {17},
  number = {13},
  pages = {1766},
  doi = {10.3390/polym17131766}
}
Kostenlos starten →