EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Sulfur and Peroxide Cross-Linking of Lignosulfonate-Filled Compounds Based on Acrylonitrile–Butadiene Rubber and Styrene–Butadiene Rubber

Ján Kruželák iD, Michaela Džuganová, Andrea Kvasničáková, Ján Hronkovič, Jozef Preťo iD, Ivan Chodák iD, Ivan Hudec

Polymers · 31.03.2025 · 17 (7) · 950

DOI: 10.3390/polym17070950 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 31.03.2025. Verfasst von Ján Kruželák und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Plastics, Rubber and Fibres, Faculty of Chemical and Food Technology, Slovak University of Technology in Bratislava, Radlinského 9, 812…. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 57 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Slovak Research and Development Agency, Slovak Scientific Grant Agency VEGA.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Calcium lignosulfonate was incorporated into rubber compounds based on styrene–butadiene rubber (SBR) and acrylonitrile–butadiene rubber (NBR) in amounts ranging from 10 to 60 phr. A sulfur-based curing system and a peroxide curing system consisting of dicumyl peroxide in combination with methacrylic acid zinc salt were used for cross-linking of the compounds. The aim of the work was to investigate the influence of lignosulfonate and curing system composition of the cross-linking process, morphology, physical–mechanical and dynamic–mechanical characteristics of the composites. The achieved results showed that peroxide cured composites demonstrated higher cross-link density, which was found not to be influenced by the content of lignosulfonate. The cross-link density of sulfur-cured composites was lower and showed a decreasing tendency with increasing amounts of the biopolymer. A lower cross-linking degree was reflected in a higher elongation at break and higher increase in the elongation at break of the corresponding composites. On the other hand, peroxide-cured composites exhibited a higher modulus M100 and higher hardness. The microscopic analysis revealed that co-agent in peroxide vulcanization contributed to the improvement of adhesion between the biopolymer and the rubber resulting in higher tensile strength of the equivalent composites. The higher cross-link density of peroxide-cured composites caused higher restriction of the chain segments’ mobility, due to which these composites exhibited a higher glass transition temperature.

Schlagwörter

Stichwörter der Autor:innen

biopolymercross-linkingperoxide curing systempropertiesrubbersulfur curing system

Autor:innen und Institutionen

  • Department of Plastics, Rubber and Fibres, Faculty of Chemical and Food Technology, Slovak University of Technology in Bratislava, Radlinského 9, 812 37 Bratislava, Slovakia.
  • VIPO a.s., Gen. Svobodu 1069/4, 958 01 Partizánske, Slovakia.
  • Slovak Academy of Sciences, Polymer Institute, Dúbravská Cesta 9, 845 41 Bratislava, Slovakia.

ORCID-Profile: Ján Kruželák, Jozef Preťo, Ivan Chodák

Förderung

  • Slovak Research and Development Agency
  • Slovak Scientific Grant Agency VEGA

Zitieren

APA

Kruželák, J., Džuganová, M., Kvasničáková, A., Hronkovič, J., Preťo, J., Chodák, I., & Hudec, I. (2025). Sulfur and Peroxide Cross-Linking of Lignosulfonate-Filled Compounds Based on Acrylonitrile–Butadiene Rubber and Styrene–Butadiene Rubber. Polymers, 17(7), 950. https://doi.org/10.3390/polym17070950

Vancouver

Kruželák J, Džuganová M, Kvasničáková A, Hronkovič J, Preťo J, Chodák I, et al. Sulfur and Peroxide Cross-Linking of Lignosulfonate-Filled Compounds Based on Acrylonitrile–Butadiene Rubber and Styrene–Butadiene Rubber. Polymers. 2025;17(7):950. doi:10.3390/polym17070950

BibTeX
@article{Kruelk2025,
  author = {Kruželák, Ján and Džuganová, Michaela and Kvasničáková, Andrea and Hronkovič, Ján and Preťo, Jozef and Chodák, Ivan and Hudec, Ivan},
  title = {Sulfur and Peroxide Cross-Linking of Lignosulfonate-Filled Compounds Based on Acrylonitrile–Butadiene Rubber and Styrene–Butadiene Rubber},
  journal = {Polymers},
  year = {2025},
  volume = {17},
  number = {7},
  pages = {950},
  doi = {10.3390/polym17070950}
}
Infokarte | EUVIMED

Artikeldaten derzeit nicht verfügbar.

Recherche