Influence of Plasticizers on Cross-Linking Process, Morphology, and Properties of Lignosulfonate-Filled Rubber Compounds
Polymers · 01.02.2025 · 17 (3) · 393
DOI: 10.3390/polym17030393 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 01.02.2025. Verfasst von Ján Kruželák und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Plastics, Rubber and Fibres, Faculty of Chemical and Food Technology, Slovak University of Technology in Bratislava, Radlinského 9, 812…. Die Arbeit wurde bisher 14-mal zitiert (Crossref) und nennt 40 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Agentúra na Podporu Výskumu a Vývoja, Slovak Research and Development Agency.
Abstract (Originalsprache)
Calcium lignosulfonate as a biopolymer component was incorporated into acrylonitrile butadiene rubber in the amount—50 phr. Four low-molecular organic molecules—1,4-butanediol, ethylene glycol, and two glycerols with different purity—were used as plasticizers. They were applied in rubber compounds in the amount ranging from 5 to 30 phr. The influence of the plasticizers on the curing process, cross-link density, morphology, and physical–mechanical properties was investigated. The blooming of plasticizers was also under observation. The results revealed that the application of plasticizers resulted in the deceleration of the curing kinetics and reduction in torque increments, pointing to the decrease in the rubber compounds’ viscosity. This was subsequently confirmed by the rheological measurements. The plasticizers softened the rubber matrix as well as the biopolymer filler. The higher the polarity of the plasticizer, the higher the plasticizing effect on lignosulfonate. The plasticizing effect increased in the following order: 1,4-butanediol < ethylene glycol < glycerols. Softened lignosulfonate formed small, soft filler-like domains well distributed within the rubber matrix. Good compatibility and adhesion between the rubber and the biopolymer on their interface was observed, leading to the enhancement in the tensile characteristics of the vulcanizates plasticized with ethylene glycol and glycerols.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Plastics, Rubber and Fibres, Faculty of Chemical and Food Technology, Slovak University of Technology in Bratislava, Radlinského 9, 812 37 Bratislava, Slovakia.
- VIPO a.s., Gen. Svobodu 1069/4, 958 01 Partizánske, Slovakia.
ORCID-Profile: Ján Kruželák, Jozef Preťo
Förderung
- Agentúra na Podporu Výskumu a Vývoja
- Slovak Research and Development Agency
Zitieren
APA
Kruželák, J., Džuganová, M., Kvasničáková, A., Preťo, J., Hronkovič, J., & Hudec, I. (2025). Influence of Plasticizers on Cross-Linking Process, Morphology, and Properties of Lignosulfonate-Filled Rubber Compounds. Polymers, 17(3), 393. https://doi.org/10.3390/polym17030393
Vancouver
Kruželák J, Džuganová M, Kvasničáková A, Preťo J, Hronkovič J, Hudec I. Influence of Plasticizers on Cross-Linking Process, Morphology, and Properties of Lignosulfonate-Filled Rubber Compounds. Polymers. 2025;17(3):393. doi:10.3390/polym17030393
BibTeX
@article{Kruelk2025,
author = {Kruželák, Ján and Džuganová, Michaela and Kvasničáková, Andrea and Preťo, Jozef and Hronkovič, Ján and Hudec, Ivan},
title = {Influence of Plasticizers on Cross-Linking Process, Morphology, and Properties of Lignosulfonate-Filled Rubber Compounds},
journal = {Polymers},
year = {2025},
volume = {17},
number = {3},
pages = {393},
doi = {10.3390/polym17030393}
}
EUVIMED