Numerical Modelling of Hybrid Polymer Composite Frame for Selected Construction Parts and Experimental Validation of Mechanical Properties
Polymers · 11.01.2025 · 17 (2) · 168
DOI: 10.3390/polym17020168 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 11.01.2025. Verfasst von Tegginamath Akshat und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Machine Parts and Mechanism, Faculty of Mechanical Engineering, Technical University of Liberec, Studentská 1402/2, 46117 Liberec, Czec…. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 54 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministry of Education, Youth and Sports of the Czech Republic and the European Union (European Structural and Investment Funds - Operational Programme Research…, Ministry of Education, Youth and Sports of the Czech Republic and the European Union, Internal grant agency of the Faculty of Engineering, Czech University of Life Sciences, Prague.
Abstract (Originalsprache)
This article is a numerical and experimental study of the mechanical properties of different glass, flax and hybrid composites. By utilizing hybrid composites consisting of natural fibers, the aim is to eventually reduce the percentage usage of synthetic or man-made fibers in composites and obtain similar levels of mechanical properties that are offered by composites using synthetic fibers. This in turn would lead to greener composites being utilized. The advantage of which would be the presence of similar mechanical properties as those of composites made from synthetic fibers along with a reduction in the overall weight of components, leading to much more eco-friendly vehicles. Finite element simulations (FEM) of mechanical properties were performed using ANSYS. The FEM simulations and analysis were performed using standards as required. Subsequently, actual beams/frames with a defined geometry were fabricated for applications in automotive body construction. The tensile performance of such frames was also simulated using ANSYS-based models and was experimentally verified. A correlation with the results of the FEM simulations of mechanical properties was established. The maximum tensile strength of 415 MPa was found for sample 1: G-E (glass–epoxy composite) and the minimum strength of 146 MPa was found for sample 2: F-G-E (G-4) (flax–glass–epoxy composite). The trends were similar, as obtained by simulation using ANSYS. A comparison of the results showed the accuracy of the numerical simulation and experimental specimens with a maximum error of about 8.05%. The experimental study of the tensile properties of polymer matrix composites was supplemented with interlaminar shear strength, and a high accuracy was found. Further, the maximum interlaminar shear strength (ILSS) of 18.5 MPa was observed for sample 1: G-E and the minimum ILSS of 17.0 MPa was observed for sample 2: F-G-E (G-4). The internal fractures were analyzed using a computer tomography analyzer (CTAn). Sample 2: F-G-E (G-4) showed significant interlaminar cracking, while sample 1: G-E showed fiber failure through the cross section rather than interlaminar failure. The results indicate a practical solution of a polymer composite frame as a replacement for existing heavier components in a car, thus helping towards weight reduction and fuel efficiency.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Machine Parts and Mechanism, Faculty of Mechanical Engineering, Technical University of Liberec, Studentská 1402/2, 46117 Liberec, Czech Republic.
- Department of Material Science and Manufacturing Technology, Faculty of Engineering, Czech University of Life Sciences Prague, Kamycka 129, 16500 Prague, Czech Republic.
ORCID-Profile: Michal Petru, Rajesh Kumar Mishra
Förderung
- Ministry of Education, Youth and Sports of the Czech Republic and the European Union (European Structural and Investment Funds - Operational Programme Research…
- Ministry of Education, Youth and Sports of the Czech Republic and the European Union
- Internal grant agency of the Faculty of Engineering, Czech University of Life Sciences, Prague
Zitieren
APA
Akshat, T., Petru, M., & Mishra, R. K. (2025). Numerical Modelling of Hybrid Polymer Composite Frame for Selected Construction Parts and Experimental Validation of Mechanical Properties. Polymers, 17(2), 168. https://doi.org/10.3390/polym17020168
Vancouver
Akshat T, Petru M, Mishra RK. Numerical Modelling of Hybrid Polymer Composite Frame for Selected Construction Parts and Experimental Validation of Mechanical Properties. Polymers. 2025;17(2):168. doi:10.3390/polym17020168
BibTeX
@article{Akshat2025,
author = {Akshat, Tegginamath and Petru, Michal and Mishra, Rajesh Kumar},
title = {Numerical Modelling of Hybrid Polymer Composite Frame for Selected Construction Parts and Experimental Validation of Mechanical Properties},
journal = {Polymers},
year = {2025},
volume = {17},
number = {2},
pages = {168},
doi = {10.3390/polym17020168}
}
EUVIMED