EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Tailoring UV Penetration Depth in Photopolymer Nanocomposites: Advancing SLA 3D Printing Performance with Nanofillers

Khalid Haj Ahmad iD, Zurina Mohamad iD, Zahid Iqbal Khan iD, Muddasar Habib

Polymers · 01.01.2025 · 17 (1) · 97

DOI: 10.3390/polym17010097 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 01.01.2025. Verfasst von Khalid Haj Ahmad und 3 weiteren Autor:innen. Beteiligte Einrichtung: College of Engineering, Alfaisal University, P.O. Box 50927, Riyadh 11533, Saudi Arabia. Die Arbeit wurde bisher 43-mal zitiert (Crossref) und nennt 24 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study examines the influence of nanofillers on the ultraviolet (UV) penetration depth of photopolymer resins used in stereolithography (SLA) 3D printing, and their impact on printability. Three nanofillers, multiwalled carbon nanotubes (MWCNT), graphene nanoplatelets (xGNP), and boron nitride nanoparticles (BNNP), were incorporated into a commercially available photopolymer resin to prepare nanocomposite formulations. The UV penetration depth (Dp) was assessed using the Windowpane method, revealing a significant reduction with the addition of nanofillers. At a concentration of 0.25 wt.%, MWCNT showed the highest reduction in Dp (90%), followed by xGNP (65%) and BNNP (33%). SLA 3D printing was performed at varying nanofiller concentrations to evaluate printability. The findings highlight a strong correlation between Dp and the maximum printable nanofiller concentration, with MWCNT limiting printability to 0.05 wt.% due to its low Dp, while BNNP allowed printing up to 1.5 wt.%. Mechanical testing showed substantial improvements in hardness and elastic modulus, even at low nanofiller concentrations, with BNNP outperforming other fillers. Compared to a clear photopolymer, the elastic modulus for 3D printed nanocomposite samples with 0.05 wt.% nanofiller compositions showed an improvement of 43% for MWCNT, 63% for xGNP, and 104% for BNNP. The hardness results showed an improvement of 86% for MWCNT, 103% for xGNP, and 179% for BNNP. These results underscore the importance of Dp in determining the layer thickness and print success in SLA 3D printing. Practical applications include the design of advanced photopolymer nanocomposites for biomedical devices, electronics, and lightweight structural components. This research provides valuable insights for tailoring material properties to meet the demands of high-performance additive manufacturing.

Schlagwörter

Stichwörter der Autor:innen

3D printingnanocompositespenetration depthphotopolymer

Autor:innen und Institutionen

  • College of Engineering, Alfaisal University, P.O. Box 50927, Riyadh 11533, Saudi Arabia.
  • Faculty of Chemical and Energy Engineering, Universiti Teknologi Malaysia, Johor Bahru 81310 UTM, Johor, Malaysia.
  • Department of Chemical Engineering, University of Engineering and Technology, Peshawar 25000, Pakistan.

ORCID-Profile: Khalid Haj Ahmad, Zurina Mohamad, Zahid Iqbal Khan

Zitieren

APA

Ahmad, K. H., Mohamad, Z., Khan, Z. I., & Habib, M. (2025). Tailoring UV Penetration Depth in Photopolymer Nanocomposites: Advancing SLA 3D Printing Performance with Nanofillers. Polymers, 17(1), 97. https://doi.org/10.3390/polym17010097

Vancouver

Ahmad KH, Mohamad Z, Khan ZI, Habib M. Tailoring UV Penetration Depth in Photopolymer Nanocomposites: Advancing SLA 3D Printing Performance with Nanofillers. Polymers. 2025;17(1):97. doi:10.3390/polym17010097

BibTeX
@article{Ahmad2025,
  author = {Ahmad, Khalid Haj and Mohamad, Zurina and Khan, Zahid Iqbal and Habib, Muddasar},
  title = {Tailoring UV Penetration Depth in Photopolymer Nanocomposites: Advancing SLA 3D Printing Performance with Nanofillers},
  journal = {Polymers},
  year = {2025},
  volume = {17},
  number = {1},
  pages = {97},
  doi = {10.3390/polym17010097}
}
Kostenlos starten →