EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Additively Manufactured Carbon Fibre PETG Composites: Effect of Print Parameters on Mechanical Properties

Andreas L Economides, Md Niamul Islam, Konstantinos P Baxevanakis iD

Polymers · 28.11.2024 · 16 (23) · 3336

DOI: 10.3390/polym16233336 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 28.11.2024. Verfasst von Andreas L Economides und 2 weiteren Autor:innen. Beteiligte Einrichtung: Wolfson School of Mechanical, Electrical and Manufacturing Engineering, Loughborough University, Loughborough LE11 3TU, UK. Die Arbeit wurde bisher 20-mal zitiert (Crossref) und nennt 42 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study investigates the quasi-static and viscoelastic properties of additively manufactured (AM) PETG reinforced with short carbon fibres. Samples were manufactured using different parameters in terms of the infill pattern, porosity, and annealing condition. Tensile and compressive tests were conducted to determine quasi-static properties such as Young’s modulus and toughness, and dynamic mechanical analysis was used under a frequency sweep of 1–100 Hz to describe the viscoelastic behaviour of the composites. The major impacts and responses between the print parameters were quantified using Analyses of Variance (ANOVAs), which revealed the major contributor to each mechanical property. Fractography on the tensile samples using scanning electron microscopy demonstrated fibre pull-out, indicating poor fibre–matrix bonding, but also revealed interfacial bonding between raster lines in the annealed samples. This had a prominent effect on the properties of latitudinal samples where the force applied was perpendicular to the raster lines. Generally, porosity appeared to have the greatest contribution to the variance in the mechanical properties, with the exception of the tensile modulus, where the infill pattern had a more substantial effect. Annealing caused a consistent increase in the tensile modulus of the tested samples, which can be used to support the design and optimisation of AM parts when they are used under specific loading conditions.

Schlagwörter

Stichwörter der Autor:innen

additive manufacturingcarbon fibrescomposite materialcompressivedynamic mechanical analysisquasi-statictensileviscoelastic characterisation

Autor:innen und Institutionen

  • Wolfson School of Mechanical, Electrical and Manufacturing Engineering, Loughborough University, Loughborough LE11 3TU, UK.

ORCID-Profile: Konstantinos P Baxevanakis

Zitieren

APA

Economides, A. L., Islam, M. N., & Baxevanakis, K. P. (2024). Additively Manufactured Carbon Fibre PETG Composites: Effect of Print Parameters on Mechanical Properties. Polymers, 16(23), 3336. https://doi.org/10.3390/polym16233336

Vancouver

Economides AL, Islam MN, Baxevanakis KP. Additively Manufactured Carbon Fibre PETG Composites: Effect of Print Parameters on Mechanical Properties. Polymers. 2024;16(23):3336. doi:10.3390/polym16233336

BibTeX
@article{Economides2024,
  author = {Economides, Andreas L and Islam, Md Niamul and Baxevanakis, Konstantinos P},
  title = {Additively Manufactured Carbon Fibre PETG Composites: Effect of Print Parameters on Mechanical Properties},
  journal = {Polymers},
  year = {2024},
  volume = {16},
  number = {23},
  pages = {3336},
  doi = {10.3390/polym16233336}
}
Kostenlos starten →