EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Investigation of Temperature at Al/Glass Fiber-Reinforced Polymer Interfaces When Drilling Composites of Different Stacking Arrangements

Brahim Salem, Ali Mkaddem iD, Malek Habak iD, Yousef Dobah iD, Makram Elfarhani iD, Abdessalem Jarraya iD

Polymers · 06.10.2024 · 16 (19) · 2823

DOI: 10.3390/polym16192823 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 06.10.2024. Verfasst von Brahim Salem und 5 weiteren Autor:innen. Beteiligte Einrichtung: LA2MP, National School of Engineering of Sfax, University of Sfax, Sfax 3038, Tunisia. Die Arbeit wurde bisher 8-mal zitiert (Crossref) und nennt 24 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Deputyship for Research & Innovation, Ministry of Education in Saudi Arabia.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This attempt covers an investigation of cutting temperature at interfaces of Fiber Metal Laminates (FMLs) made of glass fiber-reinforced polymer (GFRP) stacked with an Al2020 alloy. GFRP/Al/GFRP and Al/GFRP/Al composite stacks are both investigated to highlight the effect of stacking arrangement on thermal behavior within the interfaces. In a first test series, temperature history is recorded within the metal/composite stack interfaces using preinstalled thermocouples. In a second test series, a wireless telemetry system connected to K-type thermocouples implanted adjacent to the cutting edge of the solid carbide drill is used to record temperature evolution at the tool tip. Focus is put on the effects of cutting speed and stacking arrangement on the thrust force, drilling temperature, and delamination. From findings, the temperature histories show high sensitivity to the cutting speed. When cutting Al/GFRP/Al, the peak temperature is found to be much higher than that recorded in GFRP/Al/GFRP and exceeds the glass transition point of the GFRP matrix under critical cutting speeds. However, thrust force obtained at constitutive phases exhibits close magnitude when the stacking arrangement varies, regardless of cutting speed. Damage analysis is also discussed through the delamination factor at different stages of FML thickness.

Schlagwörter

Stichwörter der Autor:innen

GFRP/Al interfacedelaminationdrillingstacking arrangementtemperaturethrust force

Autor:innen und Institutionen

  • LA2MP, National School of Engineering of Sfax, University of Sfax, Sfax 3038, Tunisia.
  • Department of Mechanical and Materials Engineering, FOE, University of Jeddah, Jeddah 21589, Saudi Arabia.
  • Laboratoire Roberval, Centre de Recherche de Royallieu, Université de Technologie de Compiègne, Rue du Docteur Schweitzer, CS 60319, 60203 Compiègne, France.

ORCID-Profile: Ali Mkaddem, Malek Habak, Yousef Dobah, Makram Elfarhani, Abdessalem Jarraya

Förderung

  • Deputyship for Research & Innovation, Ministry of Education in Saudi Arabia

Zitieren

APA

Salem, B., Mkaddem, A., Habak, M., Dobah, Y., Elfarhani, M., & Jarraya, A. (2024). Investigation of Temperature at Al/Glass Fiber-Reinforced Polymer Interfaces When Drilling Composites of Different Stacking Arrangements. Polymers, 16(19), 2823. https://doi.org/10.3390/polym16192823

Vancouver

Salem B, Mkaddem A, Habak M, Dobah Y, Elfarhani M, Jarraya A. Investigation of Temperature at Al/Glass Fiber-Reinforced Polymer Interfaces When Drilling Composites of Different Stacking Arrangements. Polymers. 2024;16(19):2823. doi:10.3390/polym16192823

BibTeX
@article{Salem2024,
  author = {Salem, Brahim and Mkaddem, Ali and Habak, Malek and Dobah, Yousef and Elfarhani, Makram and Jarraya, Abdessalem},
  title = {Investigation of Temperature at Al/Glass Fiber-Reinforced Polymer Interfaces When Drilling Composites of Different Stacking Arrangements},
  journal = {Polymers},
  year = {2024},
  volume = {16},
  number = {19},
  pages = {2823},
  doi = {10.3390/polym16192823}
}
Kostenlos starten →