EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Machine Learning Models in Drilling of Different Types of Glass-Fiber-Reinforced Polymer Composites

Katarzyna Biruk-Urban iD, Paul Bere iD, Jerzy Józwik iD

Polymers · 03.12.2023 · 15 (23) · 4609

DOI: 10.3390/polym15234609 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 03.12.2023. Verfasst von Katarzyna Biruk-Urban und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Production Engineering, Mechanical Engineering Faculty, Lublin University of Technology, 20-618 Lublin, Poland. Die Arbeit wurde bisher 21-mal zitiert (Crossref) und nennt 46 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: The activities of the Polish Metrological Union are financed from the funds of the Ministry of Education and Scienceas part of a targeted subsidy for the imple…, Ministry of Education and Science, Lublin University of Technology.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The aim of the research presented in this paper was to simulate the relationship between selected technological drilling parameters (cutting speed, vc, and feed per tooth, fz) and cutting forces and the delamination in machining of a new glass-fiber-reinforced polymer (GFRP) composite. Four different types of new materials were manufactured with the use of a specially designed pressing device and differed in the fiber type (plain and twill woven materials) and weight fraction (wf) ratio, but they had the same number of layers and the same stacking sequence. A vertical machining center Avia VMC800HS was used for drilling holes with a two-edge carbide diamond coated drill. Measurements of the cutting force Fz in the drilling process conducted with variable technological parameters were carried out on a special test stand, 9257B, from Kistler. The new ink penetration method, involving covering the drilled hole surface with a colored liquid that spreads over the inner surface of the hole showing damage, was used to determine the delamination area. The cause-and-effect relationship between the drilling parameters was simulated with the use of five machine learning (ML) regression models (Linear Regression; Decision Tree Regressor; Decision Tree Regressor with Ada Boost; XGBRF Regressor; Gradient Boosting Regressor). Gradient Boosting Regressor results showed that the feed per tooth had the greatest impact on delamination—the higher the feed was, the greater the delamination became. Push-out delamination factors had higher values for materials that were made of plain woven fibers. The lowest amplitude of the cutting force component Fz was obtained for the lowest tested feed per tooth of 0.04 mm for all tested materials, with the lowest values obtained for the materials with twill fibers.

Schlagwörter

Stichwörter der Autor:innen

Glass-Fiber-Reinforced Polymer (GFRP)cutting forcedelaminationdrillingmachine learning (ML)

Autor:innen und Institutionen

  • Department of Production Engineering, Mechanical Engineering Faculty, Lublin University of Technology, 20-618 Lublin, Poland.
  • Department of Manufacturing Engineering, Faculty of Industrial Engineering, Robotics and Production Management, Technical University of Cluj-Napoca, Memorandumului 28, 400114 Cluj-Napoca, Romania.

ORCID-Profile: Katarzyna Biruk-Urban, Paul Bere, Jerzy Józwik

Förderung

  • The activities of the Polish Metrological Union are financed from the funds of the Ministry of Education and Scienceas part of a targeted subsidy for the imple…
  • Ministry of Education and Science
  • Lublin University of Technology

Zitieren

APA

Biruk-Urban, K., Bere, P., & Józwik, J. (2023). Machine Learning Models in Drilling of Different Types of Glass-Fiber-Reinforced Polymer Composites. Polymers, 15(23), 4609. https://doi.org/10.3390/polym15234609

Vancouver

Biruk-Urban K, Bere P, Józwik J. Machine Learning Models in Drilling of Different Types of Glass-Fiber-Reinforced Polymer Composites. Polymers. 2023;15(23):4609. doi:10.3390/polym15234609

BibTeX
@article{BirukUrban2023,
  author = {Biruk-Urban, Katarzyna and Bere, Paul and Józwik, Jerzy},
  title = {Machine Learning Models in Drilling of Different Types of Glass-Fiber-Reinforced Polymer Composites},
  journal = {Polymers},
  year = {2023},
  volume = {15},
  number = {23},
  pages = {4609},
  doi = {10.3390/polym15234609}
}
Kostenlos starten →