The Rheology of Polyether Ether Ketone Concentrated Suspensions for Powder Molding and 3D Printing
Polymers · 10.07.2024 · 16 (14) · 1973
DOI: 10.3390/polym16141973 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 10.07.2024. Verfasst von Svetlana Yu Khashirova und 7 weiteren Autor:innen. Beteiligte Einrichtung: Progressive Materials and Additive Technologies Center, N.M. Bberberov Kabardino-Balkarsky State University, 123, Chernyshevsky Str., 360004 Nalchik,…. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 21 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Russian Science Foundation.
Abstract (Originalsprache)
The main goal of the work was to use rheological methods for assessing the properties of a composition based on polyether ether ketone (PEEK) to determine the concentration limits of the polymer in the composition and select the optimal content of this composition for powder molding. The rheological properties of highly filled suspensions based on PEEK and paraffin, as well as in paraffin–polyethylene mixtures at various component ratios, were studied. These materials are designed for powder injection molding and 3D printing. Suspensions with a PEEK powder content above 50% are not capable of flow and, with increasing pressure, slide along the surface of the channel. For compositions with a higher content (60 and 70 vol.%) PEEK, independence of the storage modulus from frequency is observed, which is typical for solids and confirms the assignment of such suspensions to elastic–plastic media. The introduction of high-density polyethylene into the composition helps improve the technological properties of suspensions, expanding the range of fluidity, although it leads to an increase in viscosity. In suspensions with a mixed composition of the liquid phase, with increasing temperature, a decrease in the storage modulus is observed at 120 °C and, on the contrary, an increase at 180 °C. The latter may be a consequence of the evaporation of paraffin and the softening of PEEK due to the approach to the glass transition temperature of the polymer. Suspensions with 40% PEEK content have an optimal set of rheological properties for powder injection molding. A 3D printing filament was also obtained from a composition with 40% PEEK, which had good technological properties for FDM 3D printing. Products of satisfactory quality from suspensions with 50% PEEK can be produced by powder injection molding, but not by 3D printing. The selected compositions were used to obtain real PEEK products for practical applications.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Progressive Materials and Additive Technologies Center, N.M. Bberberov Kabardino-Balkarsky State University, 123, Chernyshevsky Str., 360004 Nalchik, Russia.
- Topchiev Institute of Petrochemical Synthesis, Russian Academy of Sciences, 119919 Moscow, Russia.
ORCID-Profile: Azamat L Slonov, Azamat A Zhansitov, Anton V Mityukov, Alexander Ya Malkin
Förderung
- Russian Science Foundation
Zitieren
APA
Khashirova, S. Y., Slonov, A. L., Zhansitov, A. A., Musov, K. V., Tlupov, A. F., Khashirov, A. A., Mityukov, A. V., & Malkin, A. Y. (2024). The Rheology of Polyether Ether Ketone Concentrated Suspensions for Powder Molding and 3D Printing. Polymers, 16(14), 1973. https://doi.org/10.3390/polym16141973
Vancouver
Khashirova SY, Slonov AL, Zhansitov AA, Musov KV, Tlupov AF, Khashirov AA, et al. The Rheology of Polyether Ether Ketone Concentrated Suspensions for Powder Molding and 3D Printing. Polymers. 2024;16(14):1973. doi:10.3390/polym16141973
BibTeX
@article{Khashirova2024,
author = {Khashirova, Svetlana Yu and Slonov, Azamat L and Zhansitov, Azamat A and Musov, Khasan V and Tlupov, Aslanbek F and Khashirov, Azamat A and Mityukov, Anton V and Malkin, Alexander Ya},
title = {The Rheology of Polyether Ether Ketone Concentrated Suspensions for Powder Molding and 3D Printing},
journal = {Polymers},
year = {2024},
volume = {16},
number = {14},
pages = {1973},
doi = {10.3390/polym16141973}
}
EUVIMED