EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Selection and Optimization of Carbon-Reinforced Polyether Ether Ketone Process Parameters in 3D Printing—A Rotating Component Application

Raja Subramani iD, Praveenkumar Vijayakumar iD, Maher Ali Rusho, Anil Kumar iD, Karthik Venkitaraman Shankar iD, Arun Kumar Thirugnanasambandam iD

Polymers · 20.05.2024 · 16 (10) · 1443

DOI: 10.3390/polym16101443 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 20.05.2024. Verfasst von Raja Subramani und 5 weiteren Autor:innen. Beteiligte Einrichtung: Center for Sustainable Materials and Surface Metamorphosis, Chennai Institute of Technology, Chennai 600069, India. Die Arbeit wurde bisher 28-mal zitiert (Crossref) und nennt 47 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: This work is partially funded by Center for Sustainable Materials and Surface Metamorphosis. Chennai institute of technology, India, Center for Sustainable Materials and Surface Metamorphosis, Chennai Institute of Technology, India.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The selection of process parameters is crucial in 3D printing for product manufacturing. These parameters govern the operation of production machinery and influence the mechanical properties, production time, and other aspects of the final product. The optimal process parameter settings vary depending on the product and printing application. This study identifies the most suitable cluster of process parameters for producing rotating components, specifically impellers, using carbon-reinforced Polyether Ether Ketone (CF-PEEK) thermoplastic filament. A mathematical programming technique using a rating method was employed to select the appropriate process parameters. The research concludes that an infill density of 70%, a layer height of 0.15 mm, a printing speed of 60 mm/s, a platform temperature of 195 °C, an extruder temperature of 445 °C, and an extruder travel speed of 95 mm/s are optimal process parameters for manufacturing rotating components using carbon-reinforced PEEK material.

Schlagwörter

Stichwörter der Autor:innen

Fuzzy-AHP-TOPSISMCDMMaterial Extrusionadditive manufacturingcarbon-reinforced Polyether Ether Ketoneoptimizationprocess parameter selection

Autor:innen und Institutionen

  • Center for Sustainable Materials and Surface Metamorphosis, Chennai Institute of Technology, Chennai 600069, India.
  • Department of Mechanical Engineering, Amrita Vishwa Vidyapeetham, Amirtapuri 690525, India.
  • Lockheed Martin Engineering Management, University of Colorado, Boulder, CO 80308, USA.
  • Department of Mechanical Engineering, Kamala Nehru Institute of Technology, Sultanpur 228118, India.
  • Centre for Flexible Electronics and Advanced Materials, Amrita Vishwa Vidyapeetham, Amritapuri 690525, India.

ORCID-Profile: Raja Subramani, Praveenkumar Vijayakumar, Anil Kumar, Karthik Venkitaraman Shankar, Arun Kumar Thirugnanasambandam

Förderung

  • This work is partially funded by Center for Sustainable Materials and Surface Metamorphosis. Chennai institute of technology, India
  • Center for Sustainable Materials and Surface Metamorphosis
  • Chennai Institute of Technology, India

Zitieren

APA

Subramani, R., Vijayakumar, P., Rusho, M. A., Kumar, A., Shankar, K. V., & Thirugnanasambandam, A. K. (2024). Selection and Optimization of Carbon-Reinforced Polyether Ether Ketone Process Parameters in 3D Printing—A Rotating Component Application. Polymers, 16(10), 1443. https://doi.org/10.3390/polym16101443

Vancouver

Subramani R, Vijayakumar P, Rusho MA, Kumar A, Shankar KV, Thirugnanasambandam AK. Selection and Optimization of Carbon-Reinforced Polyether Ether Ketone Process Parameters in 3D Printing—A Rotating Component Application. Polymers. 2024;16(10):1443. doi:10.3390/polym16101443

BibTeX
@article{Subramani2024,
  author = {Subramani, Raja and Vijayakumar, Praveenkumar and Rusho, Maher Ali and Kumar, Anil and Shankar, Karthik Venkitaraman and Thirugnanasambandam, Arun Kumar},
  title = {Selection and Optimization of Carbon-Reinforced Polyether Ether Ketone Process Parameters in 3D Printing—A Rotating Component Application},
  journal = {Polymers},
  year = {2024},
  volume = {16},
  number = {10},
  pages = {1443},
  doi = {10.3390/polym16101443}
}
Kostenlos starten →