The Development of Biocomposite Filaments for 3D Printing by Utilizing a Polylactic Acid (PLA) Polymer Matrix Reinforced with Cocoa Husk Cellulose Fibers
Polymers · 21.06.2024 · 16 (13) · 1757
DOI: 10.3390/polym16131757 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 21.06.2024. Verfasst von Victor Hugo Martins de Almeida und 7 weiteren Autor:innen. Beteiligte Einrichtung: Department of Engineering and Computing, State University of Santa Cruz (UESC), Jorge Amado Highway, Km 16, Ilhéus 45662-900, Bahia, Brazil. Die Arbeit wurde bisher 19-mal zitiert (Crossref) und nennt 29 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: UESC.
Abstract (Originalsprache)
Vegetable fibers are increasingly used in biocomposites, but there is a need for further development in utilizing by-products like cocoa husks. Three-dimensional printing, through Fused Filament Fabrication (FFF), is advancing rapidly and may be of great interest for applying biocomposite materials. This study focuses on developing innovative and fully biodegradable filaments for the FFF process. PLA filaments were prepared using cellulose fibers derived from cocoa husks (5% mass ratio). One set of filaments incorporated fibers from untreated husks (UCFFs), while another set utilized fibers from chemically treated husks (TCFFs). The fabricated materials were analyzed using scanning electron microscopy (SEM), thermogravimetric analysis (TGA), and Fourier transform infrared (FTIR) techniques, and they were also tested for tensile strength. ANOVA reveals that both UCFFs and TCFFs significantly predict tensile strength, with the UCFFs demonstrating an impressive R2 value of 0.9981. The optimal tensile strength for the filament test specimens was 16.05 MPa for TCFF8 and 13.58 MPa for UCFF8, utilizing the same printing parameters: 70% infill and a layer thickness of 0.10 mm. Additionally, there was an 18% improvement in the tensile strength of the printed specimens using the filaments filled with chemically treated cocoa husk fibers compared to the filaments with untreated fibers.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Engineering and Computing, State University of Santa Cruz (UESC), Jorge Amado Highway, Km 16, Ilhéus 45662-900, Bahia, Brazil.
- Department of Exact Sciences, State University of Santa Cruz (UESC), Jorge Amado Highway, Km 16, Ilhéus 45662-900, Bahia, Brazil.
ORCID-Profile: Victor Hugo Martins de Almeida, Raildo Mota de Jesus, Gregório Mateus Santana, Sabir Khan, Erickson Fabiano Moura Sousa Silva, Paulo Neilson Marques Dos Anjos
Förderung
- UESC
Zitieren
APA
Almeida, V. H. M., Jesus, R. M., Santana, G. M., Khan, S., Silva, E. F. M. S., Cruz, I. S. D., Santos, I. S., & Dos Anjos, P. N. M. (2024). The Development of Biocomposite Filaments for 3D Printing by Utilizing a Polylactic Acid (PLA) Polymer Matrix Reinforced with Cocoa Husk Cellulose Fibers. Polymers, 16(13), 1757. https://doi.org/10.3390/polym16131757
Vancouver
Almeida VHM, Jesus RM, Santana GM, Khan S, Silva EFMS, Cruz ISD, et al. The Development of Biocomposite Filaments for 3D Printing by Utilizing a Polylactic Acid (PLA) Polymer Matrix Reinforced with Cocoa Husk Cellulose Fibers. Polymers. 2024;16(13):1757. doi:10.3390/polym16131757
BibTeX
@article{Almeida2024,
author = {Almeida, Victor Hugo Martins de and Jesus, Raildo Mota de and Santana, Gregório Mateus and Khan, Sabir and Silva, Erickson Fabiano Moura Sousa and Cruz, Iago Silva da and Santos, Ian de Souza and Dos Anjos, Paulo Neilson Marques},
title = {The Development of Biocomposite Filaments for 3D Printing by Utilizing a Polylactic Acid (PLA) Polymer Matrix Reinforced with Cocoa Husk Cellulose Fibers},
journal = {Polymers},
year = {2024},
volume = {16},
number = {13},
pages = {1757},
doi = {10.3390/polym16131757}
}
EUVIMED