EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Thermo-Mechanical Behavior and Strain Rate Sensitivity of 3D-Printed Polylactic Acid (PLA) below Glass Transition Temperature (Tg)

Vukašin Slavković iD, Blaž Hanželič, Vasja Plesec iD, Strahinja Milenković iD, Gregor Harih

Polymers · 29.05.2024 · 16 (11) · 1526

DOI: 10.3390/polym16111526 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 29.05.2024. Verfasst von Vukašin Slavković und 4 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Engineering, University of Kragujevac, Sestre Janjic 6, 34000 Kragujevac, Serbia. Die Arbeit wurde bisher 70-mal zitiert (Crossref) und nennt 81 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Slovenian research and innovation agency.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study investigated the thermomechanical behavior of 4D-printed polylactic acid (PLA), focusing on its response to varying temperatures and strain rates in a wide range below the glass transition temperature (Tg). The material was characterized using tension, compression, and dynamic mechanical thermal analysis (DMTA), confirming PLA’s strong dependency on strain rate and temperature. The glass transition temperature of 4D-printed PLA was determined to be 65 °C using a thermal analysis (DMTA). The elastic modulus changed from 1045.7 MPa in the glassy phase to 1.2 MPa in the rubber phase, showing the great shape memory potential of 4D-printed PLA. The filament tension tests revealed that the material’s yield stress strongly depended on the strain rate at room temperature, with values ranging from 56 MPa to 43 MPA as the strain rate decreased. Using a commercial FDM Ultimaker printer, cylindrical compression samples were 3D-printed and then characterized under thermo-mechanical conditions. Thermo-mechanical compression tests were conducted at strain rates ranging from 0.0001 s−1 to 0.1 s−1 and at temperatures below the glass transition temperature (Tg) at 25, 37, and 50 °C. The conducted experimental tests showed that the material had distinct yield stress, strain softening, and strain hardening at very large deformations. Clear strain rate dependence was observed, particularly at quasi-static rates, with the temperature and strain rate significantly influencing PLA’s mechanical properties, including yield stress. Yield stress values varied from 110 MPa at room temperature with a strain rate of 0.1 s−1 to 42 MPa at 50 °C with a strain rate of 0.0001 s−1. This study also included thermo-mechanical adiabatic tests, which revealed that higher strain rates of 0.01 s−1 and 0.1 s−1 led to self-heating due to non-dissipated generated heat. This internal heating caused additional softening at higher strain rates and lower stress values. Thermal imaging revealed temperature increases of 15 °C and 18 °C for strain rates of 0.01 s−1 and 0.1 s−1, respectively.

Schlagwörter

Stichwörter der Autor:innen

3D printing4D printingshape memory polymersmart materialsthermo-mechanical experiments

Autor:innen und Institutionen

  • Faculty of Engineering, University of Kragujevac, Sestre Janjic 6, 34000 Kragujevac, Serbia.
  • Laboratory for Integrated Product Development and CAD, Faculty of Mechanical Engineering, University of Maribor, Smetanova ulica 17, SI-2000 Maribor, Slovenia.

ORCID-Profile: Vukašin Slavković, Vasja Plesec, Strahinja Milenković

Förderung

  • Slovenian research and innovation agency

Zitieren

APA

Slavković, V., Hanželič, B., Plesec, V., Milenković, S., & Harih, G. (2024). Thermo-Mechanical Behavior and Strain Rate Sensitivity of 3D-Printed Polylactic Acid (PLA) below Glass Transition Temperature (Tg). Polymers, 16(11), 1526. https://doi.org/10.3390/polym16111526

Vancouver

Slavković V, Hanželič B, Plesec V, Milenković S, Harih G. Thermo-Mechanical Behavior and Strain Rate Sensitivity of 3D-Printed Polylactic Acid (PLA) below Glass Transition Temperature (Tg). Polymers. 2024;16(11):1526. doi:10.3390/polym16111526

BibTeX
@article{Slavkovi2024,
  author = {Slavković, Vukašin and Hanželič, Blaž and Plesec, Vasja and Milenković, Strahinja and Harih, Gregor},
  title = {Thermo-Mechanical Behavior and Strain Rate Sensitivity of 3D-Printed Polylactic Acid (PLA) below Glass Transition Temperature (Tg)},
  journal = {Polymers},
  year = {2024},
  volume = {16},
  number = {11},
  pages = {1526},
  doi = {10.3390/polym16111526}
}
Kostenlos starten →