EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Investigation of the Effectiveness of Silicon Nitride as a Reinforcement Agent for Polyethylene Terephthalate Glycol in Material Extrusion 3D Printing

Nikolaos Michailidis iD, Markos Petousis iD, Vassilis Saltas iD, Vassilis Papadakis iD, Mariza Spiridaki iD, Nikolaos Mountakis iD, Apostolos Argyros iD, John Valsamos, Nektarios K Nasikas, Nectarios Vidakis

Polymers · 10.04.2024 · 16 (8) · 1043

DOI: 10.3390/polym16081043 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 10.04.2024. Verfasst von Nikolaos Michailidis und 9 weiteren Autor:innen. Beteiligte Einrichtung: Physical Metallurgy Laboratory, Mechanical Engineering Department, School of Engineering, Aristotle University of Thessaloniki, 54124 Thessaloniki, G…. Die Arbeit wurde bisher 20-mal zitiert (Crossref) und nennt 86 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Polyethylene terephthalate glycol (PETG) and silicon nitride (Si3N4) were combined to create five composite materials with Si3N4 loadings ranging from 2.0 wt.% to 10.0 wt.%. The goal was to improve the mechanical properties of PETG in material extrusion (MEX) additive manufacturing (AM) and assess the effectiveness of Si3N4 as a reinforcing agent for this particular polymer. The process began with the production of filaments, which were subsequently fed into a 3D printer to create various specimens. The specimens were manufactured according to international standards to ensure their suitability for various tests. The thermal, rheological, mechanical, electrical, and morphological properties of the prepared samples were evaluated. The mechanical performance investigations performed included tensile, flexural, Charpy impact, and microhardness tests. Scanning electron microscopy and energy-dispersive X-ray spectroscopy mapping were performed to investigate the structures and morphologies of the samples, respectively. Among all the composites tested, the PETG/6.0 wt.% Si3N4 showed the greatest improvement in mechanical properties (with a 24.5% increase in tensile strength compared to unfilled PETG polymer), indicating its potential for use in MEX 3D printing when enhanced mechanical performance is required from the PETG polymer.

Schlagwörter

Stichwörter der Autor:innen

broadband dielectric spectroscopy (BDS)material extrusion (MEX)mechanical performancenanocompositespolyethylene terephthalate glycol (PETG)silicon nitride (Si3N4)three-dimensional (3D) printing

Autor:innen und Institutionen

  • Physical Metallurgy Laboratory, Mechanical Engineering Department, School of Engineering, Aristotle University of Thessaloniki, 54124 Thessaloniki, Greece.
  • Centre for Research & Development of Advanced Materials (CERDAM), Centre for Interdisciplinary Research and Innovation, Balkan Centre, Building B', 10th Km Thessaloniki-Thermi Road, 57001 Thessaloniki, Greece.
  • Department of Mechanical Engineering, Hellenic Mediterranean University, 71410 Heraklion, Greece.
  • Department of Electronic Engineering, Hellenic Mediterranean University, 73133 Chania, Greece.
  • Institute of Electronic Structure and Laser of the Foundation for Research and Technology-Hellas (IESL-FORTH)-Hellas, N. Plastira 100m, 70013 Heraklion, Greece.
  • Department of Industrial Design and Production Engineering, University of West Attica, 12243 Athens, Greece.

ORCID-Profile: Nikolaos Michailidis, Markos Petousis, Vassilis Saltas, Vassilis Papadakis, Mariza Spiridaki, Nikolaos Mountakis, Apostolos Argyros

Zitieren

APA

Michailidis, N., Petousis, M., Saltas, V., Papadakis, V., Spiridaki, M., Mountakis, N., Argyros, A., Valsamos, J., Nasikas, N. K., & Vidakis, N. (2024). Investigation of the Effectiveness of Silicon Nitride as a Reinforcement Agent for Polyethylene Terephthalate Glycol in Material Extrusion 3D Printing. Polymers, 16(8), 1043. https://doi.org/10.3390/polym16081043

Vancouver

Michailidis N, Petousis M, Saltas V, Papadakis V, Spiridaki M, Mountakis N, et al. Investigation of the Effectiveness of Silicon Nitride as a Reinforcement Agent for Polyethylene Terephthalate Glycol in Material Extrusion 3D Printing. Polymers. 2024;16(8):1043. doi:10.3390/polym16081043

BibTeX
@article{Michailidis2024,
  author = {Michailidis, Nikolaos and Petousis, Markos and Saltas, Vassilis and Papadakis, Vassilis and Spiridaki, Mariza and Mountakis, Nikolaos and Argyros, Apostolos and Valsamos, John and Nasikas, Nektarios K and Vidakis, Nectarios},
  title = {Investigation of the Effectiveness of Silicon Nitride as a Reinforcement Agent for Polyethylene Terephthalate Glycol in Material Extrusion 3D Printing},
  journal = {Polymers},
  year = {2024},
  volume = {16},
  number = {8},
  pages = {1043},
  doi = {10.3390/polym16081043}
}
Kostenlos starten →