Enhancing the Weld Quality of Polylactic Acid Biomedical Materials Using Rotary Friction Welding
Polymers · 04.04.2024 · 16 (7) · 991
DOI: 10.3390/polym16070991 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 04.04.2024. Verfasst von Chil-Chyuan Kuo und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, Ming Chi University of Technology, No. 84, Gungjuan Road, New Taipei City 24301, Taiwan. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 47 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministry of Science and Technology of Taiwan.
Abstract (Originalsprache)
Polylactic acid (PLA) stands out as a biomaterial with immense potential, primarily owing to its innate biodegradability. Conventional methods for manufacturing PLA encompass injection molding or additive manufacturing (AM). Yet, the fabrication of sizable medical devices often necessitates fragmenting them into multiple components for printing, subsequently requiring reassembly to accommodate the constraints posed by the dimensions of the AM platform. Typically, laboratories resort to employing nuts and bolts for the assembly of printed components into expansive medical devices. Nonetheless, this conventional approach of jointing is susceptible to the inherent risk of bolts and nuts loosening or dislodging amid the reciprocating movements inherent to sizable medical apparatus. Hence, investigation into the joining techniques for integrating printed components into expansive medical devices has emerged as a critical focal point within the realm of research. The main objective is to enhance the joint strength of PLA polymer rods using rotary friction welding (RFW). The mean bending strength of welded components, fabricated under seven distinct rotational speeds, surpasses that of the underlying PLA substrate material. The average bending strength improvement rate of welding parts fabricated by RFW with three-stage transformation to 4000 rpm is about 41.94% compared with the average bending strength of PLA base material. The average surface hardness of the weld interface is about 1.25 to 3.80% higher than the average surface hardness of the PLA base material. The average surface hardness of the weld interface performed by RFW with variable rotational speed is higher than the average surface hardness of the weld interface performed at a fixed rotating friction speed. The temperature rise rate and maximum temperature recorded during RFW in the X-axis of the CNC turning machine at the outer edge of the welding part surpassed those observed in the internal temperature of the welding part. Remarkably, the proposed method in this study complies with the Sustainable Development Goals due to its high energy efficiency and low environmental pollution.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Mechanical Engineering, Ming Chi University of Technology, No. 84, Gungjuan Road, New Taipei City 24301, Taiwan.
- Research Center for Intelligent Medical Devices, Ming Chi University of Technology, No. 84, Gungjuan Road, New Taipei City 24301, Taiwan.
- Department of Mechanical Engineering, Chang Gung University, No. 259, Wenhua 1st Rd., Guishan Dist., Taoyuan City 33302, Taiwan.
- Center for Reliability Engineering, Ming Chi University of Technology, No. 84, Gungjuan Road, Taishan District, New Taipei City 24301, Taiwan.
- Li-Yin Technology Co., Ltd., No. 37, Lane 151, Section 1, Zhongxing Road, Wugu District, New Taipei City 241, Taiwan.
- Department of Mechanical Engineering, National Taipei University of Technology, No. 1, Sec. 3, Zhongxiao E. Rd., Da'an Dist., Taipei City 106344, Taiwan.
ORCID-Profile: Chil-Chyuan Kuo, Shih-Feng Tseng
Förderung
- Ministry of Science and Technology of Taiwan
Zitieren
APA
Kuo, C. C., Liang, H. X., Huang, S. H., & Tseng, S. F. (2024). Enhancing the Weld Quality of Polylactic Acid Biomedical Materials Using Rotary Friction Welding. Polymers, 16(7), 991. https://doi.org/10.3390/polym16070991
Vancouver
Kuo CC, Liang HX, Huang SH, Tseng SF. Enhancing the Weld Quality of Polylactic Acid Biomedical Materials Using Rotary Friction Welding. Polymers. 2024;16(7):991. doi:10.3390/polym16070991
BibTeX
@article{Kuo2024,
author = {Kuo, Chil-Chyuan and Liang, Hua-Xhin and Huang, Song-Hua and Tseng, Shih-Feng},
title = {Enhancing the Weld Quality of Polylactic Acid Biomedical Materials Using Rotary Friction Welding},
journal = {Polymers},
year = {2024},
volume = {16},
number = {7},
pages = {991},
doi = {10.3390/polym16070991}
}
EUVIMED