The Mechanical, Thermal, and Biological Properties of Materials Intended for Dental Implants: A Comparison of Three Types of Poly(aryl-ether-ketones) (PEEK and PEKK)
Polymers · 08.09.2023 · 15 (18) · 3706
DOI: 10.3390/polym15183706 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 08.09.2023. Verfasst von Sandra Paszkiewicz und 7 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Mechanical Engineering and Mechatronics, West Pomeranian University of Technology, 70-310 Szczecin, Poland. Die Arbeit wurde bisher 38-mal zitiert (Crossref) und nennt 32 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: European Union from the European Regional Development Fund under the Regional Operational Program of the West Pomeranian Voivodeship 2014-2020. Project co-fina…, European Union from the European Regional Development Fund, Ministry of Education and Science.
Abstract (Originalsprache)
Regarding the dynamic development of 3D printing technology, as well as its application in a growing part of industries, i.e., in the automotive industry, construction industry, medical industry, etc., there is a notable opportunity for its application in producing dental implants, which presents a promising alternative to traditional implant manufacturing methods. The medical industry is very restrictive regarding the applied materials, and it is necessary to use materials that exhibit very good mechanical and thermal parameters, show clinical indifference and biocompatibility, are non-allergenic and non-cancerous, and are likely to sterilize. Such materials are poly(aryl-ether-ketone)s (PAEK)s, mainly poly(ether-ether-ketone) (PEEK) and poly(ether-ketone-ketone) (PEKK), that are found to be high-performance polymers and can be defined as materials that retain their functionality even in extreme conditions. In the present paper, two types of PEEKs and PEKK were compared regarding their structural, mechanical, and thermal properties along with the biological activity toward selected strains. The tested samples were obtained with Fused Deposition Modeling (FDM) technology. The PEKK, after heat treatment, exhibits the most promising mechanical properties as well as less bacterial adhesion on its surface when compared to both PEEKs. Consequently, among the evaluated materials, PEKK after heat treatment stands out as the optimal selection for a dental prosthesis.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Faculty of Mechanical Engineering and Mechatronics, West Pomeranian University of Technology, 70-310 Szczecin, Poland.
- Tele-Fonika Kable S.A., Factory in Bydgoszcz, 85-957 Bydgoszcz, Poland.
ORCID-Profile: Sandra Paszkiewicz, Konrad Walkowiak, Izabela Irska, Karol Miądlicki, Elżbieta Piesowicz
Förderung
- European Union from the European Regional Development Fund under the Regional Operational Program of the West Pomeranian Voivodeship 2014-2020. Project co-fina…
- European Union from the European Regional Development Fund
- Ministry of Education and Science
Zitieren
APA
Paszkiewicz, S., Lesiak, P., Walkowiak, K., Irska, I., Miądlicki, K., Królikowski, M., Piesowicz, E., & Figiel, P. (2023). The Mechanical, Thermal, and Biological Properties of Materials Intended for Dental Implants: A Comparison of Three Types of Poly(aryl-ether-ketones) (PEEK and PEKK). Polymers, 15(18), 3706. https://doi.org/10.3390/polym15183706
Vancouver
Paszkiewicz S, Lesiak P, Walkowiak K, Irska I, Miądlicki K, Królikowski M, et al. The Mechanical, Thermal, and Biological Properties of Materials Intended for Dental Implants: A Comparison of Three Types of Poly(aryl-ether-ketones) (PEEK and PEKK). Polymers. 2023;15(18):3706. doi:10.3390/polym15183706
BibTeX
@article{Paszkiewicz2023,
author = {Paszkiewicz, Sandra and Lesiak, Paweł and Walkowiak, Konrad and Irska, Izabela and Miądlicki, Karol and Królikowski, Marcin and Piesowicz, Elżbieta and Figiel, Paweł},
title = {The Mechanical, Thermal, and Biological Properties of Materials Intended for Dental Implants: A Comparison of Three Types of Poly(aryl-ether-ketones) (PEEK and PEKK)},
journal = {Polymers},
year = {2023},
volume = {15},
number = {18},
pages = {3706},
doi = {10.3390/polym15183706}
}
EUVIMED