Characterization of Material Extrusion-Printed Amorphous Poly(Ether Ketone Ketone) (PEKK) Parts
Polymers · 16.04.2025 · 17 (8) · 1069
DOI: 10.3390/polym17081069 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 16.04.2025. Verfasst von Thomas Hanemann und 5 weiteren Autor:innen. Beteiligte Einrichtung: Institute for Applied Materials, Karlsruhe Institute of Technology, Hermann-von-Helmholtz-Platz 1, D-76344 Eggenstein-Leopoldshafen, Germany. Die Arbeit wurde bisher 7-mal zitiert (Crossref) und nennt 29 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).
Abstract (Originalsprache)
Poly(ether ketone ketone) (PEKK), as a representative of high-performance poly(aryl ether ketones), shows outstanding thermomechanical properties, opening up a huge range of different applications in various technical fields. Its appearance as a quasi-amorphous polymer with a certain suppression of the crystallization process facilitates melt processing via additive manufacturing processes like material extrusion (MEX), especially in fused filament fabrication (FFF). The quality of the printing process is proven in this work by tensile testing and surface roughness measurements of suitable specimens. The MEX printing of semicrystalline PEKK faces two major challenges: on the one hand, the very high printing temperature is in contrast to established engineering plastics, and on the other hand, it is difficult to avoid crystallization after printing. The first issue can be addressed by using suitably enhanced MEX printers and the second one by selecting adapted printing parameters. The measured Young’s modulus (3.49 GPa) and tensile strength (104 MPa) values are higher than the related vendors’ data given for filaments (3.0 GPa and 92 MPa, respectively). In addition, the temperature-dependent thermal conductivity is determined, and the values of well-established PEEK (poly(ether ether ketone)) in the temperature range from 20 to 180 °C are mostly slightly higher in comparison to the related PEKK data. Based on the results, PEKK can be a useful substitute for well-established PEEK because of their comparable properties. However, PEKK has a pronouncedly lower FFF printing temperature, combined with a reduced tendency of the device to warp after printing. A larger printed test part with some surface structures shows the improved printability of PEKK in comparison to PEEK.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Institute for Applied Materials, Karlsruhe Institute of Technology, Hermann-von-Helmholtz-Platz 1, D-76344 Eggenstein-Leopoldshafen, Germany.
- Department of Microsystems Engineering, University Freiburg, Georges-Koehler-Allee 102, D-79110 Freiburg, Germany.
ORCID-Profile: Thomas Hanemann, Steffen Antusch
Zitieren
APA
Hanemann, T., Klein, A., Baumgärtner, S., Jung, J., Wilhelm, D., & Antusch, S. (2025). Characterization of Material Extrusion-Printed Amorphous Poly(Ether Ketone Ketone) (PEKK) Parts. Polymers, 17(8), 1069. https://doi.org/10.3390/polym17081069
Vancouver
Hanemann T, Klein A, Baumgärtner S, Jung J, Wilhelm D, Antusch S. Characterization of Material Extrusion-Printed Amorphous Poly(Ether Ketone Ketone) (PEKK) Parts. Polymers. 2025;17(8):1069. doi:10.3390/polym17081069
BibTeX
@article{Hanemann2025,
author = {Hanemann, Thomas and Klein, Alexander and Baumgärtner, Siegfried and Jung, Judith and Wilhelm, David and Antusch, Steffen},
title = {Characterization of Material Extrusion-Printed Amorphous Poly(Ether Ketone Ketone) (PEKK) Parts},
journal = {Polymers},
year = {2025},
volume = {17},
number = {8},
pages = {1069},
doi = {10.3390/polym17081069}
}
EUVIMED