Preparation and Effect of Methyl-Oleate-Based Polyol on the Properties of Rigid Polyurethane Foams as Potential Thermal Insulation Material
Polymers · 13.07.2023 · 15 (14) · 3028
DOI: 10.3390/polym15143028 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 13.07.2023. Verfasst von Norsuhaili Kamairudin und 4 weiteren Autor:innen. Beteiligte Einrichtung: Higher Education Centre of Excellence (HiCoE), Institute of Tropical Forestry and Forest Product, University Putra Malaysia, Serdang 43400, Selangor,…. Die Arbeit wurde bisher 18-mal zitiert (Crossref) und nennt 63 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministry of Higher Education, Malaysian Palm Oil Board (MPOB), Research Management Centre of Universiti Putra Malaysia.
Abstract (Originalsprache)
Recently, most of the commercial polyols used in the production of rigid polyurethane foams (RPUFs) have been derived from petrochemicals. Therefore, the introduction of modified palm oil derivatives-based polyol as a renewable material into the formulation of RPUFs is the focus of this study. A palm oil derivative—namely, methyl oleate (MO)—was successfully modified through three steps of reactions: epoxidation reaction, ring-opened with glycerol, followed by amidation reaction to produce a bio-based polyol named alkanolamide polyol. Physicochemical properties of the alkanolamide polyol were analyzed. The hydroxyl value of alkanolamide polyol was 313 mg KOH/g, which is suitable for producing RPUFs. Therefore, RPUFs were produced by replacing petrochemical polyol with alkanolamide polyol. The effects of alkanolamide polyol on the physical, mechanical and thermal properties were evaluated. The results showed that the apparent density and compressive strength increased, and cell size decreased, upon introducing alkanolamide polyol. All the RPUFs exhibited low water absorption and excellent dimensional stability. The RPUFs made with increased amounts of alkanolamide polyol showed higher thermal conductivity. Nevertheless, the thermal conductivities of RPUFs made with alkanolamide polyol are still within the range for thermal insulating materials (
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Higher Education Centre of Excellence (HiCoE), Institute of Tropical Forestry and Forest Product, University Putra Malaysia, Serdang 43400, Selangor, Malaysia.
- Department of Chemical and Environmental Engineering, Faculty of Engineering, University Putra Malaysia, Serdang 43400, Selangor, Malaysia.
- Malaysian Palm Oil Board, No. 6, Persiaran Institusi, Bandar Baru Bangi, Kajang 43000, Selangor, Malaysia.
- Institute of Nanoscience and Nanotechnology, Universiti Putra Malaysia, Serdang 43400, Selangor, Malaysia.
- Department of Bioprocess Technology, Faculty of Biotechnology and Biomolecular Sciences, Universiti Putra Malaysia, Serdang 43400, Selangor, Malaysia.
ORCID-Profile: Luqman Chuah Abdullah, Dayang Radiah Awang Biak, Hidayah Ariffin
Förderung
- Ministry of Higher Education
- Malaysian Palm Oil Board (MPOB)
- Research Management Centre of Universiti Putra Malaysia
Zitieren
APA
Kamairudin, N., Abdullah, L. C., Hoong, S. S., Biak, D. R. A., & Ariffin, H. (2023). Preparation and Effect of Methyl-Oleate-Based Polyol on the Properties of Rigid Polyurethane Foams as Potential Thermal Insulation Material. Polymers, 15(14), 3028. https://doi.org/10.3390/polym15143028
Vancouver
Kamairudin N, Abdullah LC, Hoong SS, Biak DRA, Ariffin H. Preparation and Effect of Methyl-Oleate-Based Polyol on the Properties of Rigid Polyurethane Foams as Potential Thermal Insulation Material. Polymers. 2023;15(14):3028. doi:10.3390/polym15143028
BibTeX
@article{Kamairudin2023,
author = {Kamairudin, Norsuhaili and Abdullah, Luqman Chuah and Hoong, Seng Soi and Biak, Dayang Radiah Awang and Ariffin, Hidayah},
title = {Preparation and Effect of Methyl-Oleate-Based Polyol on the Properties of Rigid Polyurethane Foams as Potential Thermal Insulation Material},
journal = {Polymers},
year = {2023},
volume = {15},
number = {14},
pages = {3028},
doi = {10.3390/polym15143028}
}
EUVIMED