EUVIMEDEUVIMED entdecken
ÜbersichtsarbeitOpen Access · CC BY 4.0

Adhesion of Conventional, 3D-Printed and Milled Artificial Teeth to Resin Substrates for Complete Dentures: A Narrative Review

Emmanouil-George Tzanakakis iD, Panagiotis Pandoleon, Aspasia Sarafianou iD, Eleana Kontonasaki iD

Polymers · 28.05.2023 · 15 (11) · 2488

DOI: 10.3390/polym15112488 ↗

Kurz gefasst

Übersichtsarbeit in der Zeitschrift Polymers, online erschienen am 28.05.2023. Verfasst von Emmanouil-George Tzanakakis und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, Faculty of Dentistry, School of Health Sciences, Aristotle University of Thessaloniki, 54124 Thessaloniki, Greece. Die Arbeit wurde bisher 43-mal zitiert (Crossref) und nennt 138 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Background

One type of failure in complete or partial dentures is the detachment of resin teeth from denture base resin (DBR). This common complication is also observed in the new generation of digitally fabricated dentures. The purpose of this review was to provide an update on the adhesion of artificial teeth to denture resin substrates fabricated by conventional and digital methods.

Methods

A search strategy was applied to retrieve relevant studies in PubMed and Scopus.

Results

Chemical (monomers, ethyl acetone, conditioning liquids, adhesive agents, etc.) and mechanical (grinding, laser, sandblasting, etc.) treatments are commonly used by technicians to improve denture teeth retention with controversial benefits. Better performance in conventional dentures is realized for certain combinations of DBR materials and denture teeth after mechanical or chemical treatment.

Conclusions

The incompatibility of certain materials and lack of copolymerization are the main reasons for failure. Due to the emerging field of new techniques for denture fabrication, different materials have been developed, and further research is needed to elaborate the best combination of teeth and DBRs. Lower bond strength and suboptimal failure modes have been related to 3D-printed combinations of teeth and DBRs, while milled and conventional combinations seem to be a safer choice until further improvements in printing technologies are developed.

Schlagwörter

Stichwörter der Autor:innen

3D-prinitngCAD/CAMacrylic denture teethadhesioncomplete denturesmilling

Autor:innen und Institutionen

  • Department of Prosthodontics, Faculty of Dentistry, School of Health Sciences, Aristotle University of Thessaloniki, 54124 Thessaloniki, Greece.
  • Department of Prosthodontics, School of Dentistry, National and Kapodistrian University of Athens, 2 Thivon Str., 11527 Athens, Greece.

ORCID-Profile: Emmanouil-George Tzanakakis, Aspasia Sarafianou, Eleana Kontonasaki

Zitieren

APA

Tzanakakis, E. G., Pandoleon, P., Sarafianou, A., & Kontonasaki, E. (2023). Adhesion of Conventional, 3D-Printed and Milled Artificial Teeth to Resin Substrates for Complete Dentures: A Narrative Review. Polymers, 15(11), 2488. https://doi.org/10.3390/polym15112488

Vancouver

Tzanakakis EG, Pandoleon P, Sarafianou A, Kontonasaki E. Adhesion of Conventional, 3D-Printed and Milled Artificial Teeth to Resin Substrates for Complete Dentures: A Narrative Review. Polymers. 2023;15(11):2488. doi:10.3390/polym15112488

BibTeX
@article{Tzanakakis2023,
  author = {Tzanakakis, Emmanouil-George and Pandoleon, Panagiotis and Sarafianou, Aspasia and Kontonasaki, Eleana},
  title = {Adhesion of Conventional, 3D-Printed and Milled Artificial Teeth to Resin Substrates for Complete Dentures: A Narrative Review},
  journal = {Polymers},
  year = {2023},
  volume = {15},
  number = {11},
  pages = {2488},
  doi = {10.3390/polym15112488}
}
Kostenlos starten →