EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

The Influence of the Layer Height and the Filament Color on the Dimensional Accuracy and the Tensile Strength of FDM-Printed PLA Specimens

Doina Frunzaverde iD, Vasile Cojocaru iD, Nicoleta Bacescu, Costel-Relu Ciubotariu iD, Calin-Octavian Miclosina iD, Raul Rusalin Turiac, Gabriela Marginean iD

Polymers · 19.05.2023 · 15 (10) · 2377

DOI: 10.3390/polym15102377 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 19.05.2023. Verfasst von Doina Frunzaverde und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Engineering Science, Babes-Bolyai University, Traian Vuia Square 1-4, 320085 Resita, Romania. Die Arbeit wurde bisher 100-mal zitiert (Crossref) und nennt 67 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Among the FDM process variables, one of the less addressed in previous research is the filament color. Moreover, if not explicitly targeted, the filament color is usually not even mentioned. Aiming to point out if, and to what extent, the color of the PLA filaments influences the dimensional precision and the mechanical strength of FDM prints, the authors of the present research carried out experiments on tensile specimens. The variable parameters were the layer height (0.05 mm, 0.10 mm, 0.15 mm, 0.20 mm) and the material color (natural, black, red, grey). The experimental results clearly showed that the filament color is an influential factor for the dimensional accuracy as well as for the tensile strength of the FDM printed PLA parts. Moreover, the two way ANOVA test performed revealed that the strongest effect on the tensile strength was exerted by the PLA color (η2 = 97.3%), followed by the layer height (η2 = 85.5%) and the interaction between the PLA color and the layer height (η2 = 80.0%). Under the same printing conditions, the best dimensional accuracy was ensured by the black PLA (0.17% width deviations, respectively 5.48% height deviations), whilst the grey PLA showed the highest ultimate tensile strength values (between 57.10 MPa and 59.82 MPa).

Schlagwörter

Stichwörter der Autor:innen

PLA colordimensional accuracyfilament colorfused deposition modeling (FDM)fused filament fabrication (FFF)layer heightlayer thicknesspolylactic acid (PLA)tensile strength

Autor:innen und Institutionen

  • Department of Engineering Science, Babes-Bolyai University, Traian Vuia Square 1-4, 320085 Resita, Romania.
  • Department of Materials Science and Testing, Westphalian University of Applied Sciences Gelsenkirchen Bocholt Recklinghausen, Neidenburgerstr. 43, 45897 Gelsenkirchen, Germany.

ORCID-Profile: Doina Frunzaverde, Vasile Cojocaru, Costel-Relu Ciubotariu, Calin-Octavian Miclosina, Gabriela Marginean

Zitieren

APA

Frunzaverde, D., Cojocaru, V., Bacescu, N., Ciubotariu, C. R., Miclosina, C. O., Turiac, R. R., & Marginean, G. (2023). The Influence of the Layer Height and the Filament Color on the Dimensional Accuracy and the Tensile Strength of FDM-Printed PLA Specimens. Polymers, 15(10), 2377. https://doi.org/10.3390/polym15102377

Vancouver

Frunzaverde D, Cojocaru V, Bacescu N, Ciubotariu CR, Miclosina CO, Turiac RR, et al. The Influence of the Layer Height and the Filament Color on the Dimensional Accuracy and the Tensile Strength of FDM-Printed PLA Specimens. Polymers. 2023;15(10):2377. doi:10.3390/polym15102377

BibTeX
@article{Frunzaverde2023,
  author = {Frunzaverde, Doina and Cojocaru, Vasile and Bacescu, Nicoleta and Ciubotariu, Costel-Relu and Miclosina, Calin-Octavian and Turiac, Raul Rusalin and Marginean, Gabriela},
  title = {The Influence of the Layer Height and the Filament Color on the Dimensional Accuracy and the Tensile Strength of FDM-Printed PLA Specimens},
  journal = {Polymers},
  year = {2023},
  volume = {15},
  number = {10},
  pages = {2377},
  doi = {10.3390/polym15102377}
}
Kostenlos starten →