EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

An Experimental Study on the Impact of Layer Height and Annealing Parameters on the Tensile Strength and Dimensional Accuracy of FDM 3D Printed Parts

Jelena R Stojković iD, Rajko Turudija, Nikola Vitković, Filip Górski, Ancuţa Păcurar, Alin Pleşa, Alexandru Ianoşi-Andreeva-Dimitrova iD, Răzvan Păcurar iD

Materials · 25.06.2023 · 16 (13) · 4574

DOI: 10.3390/ma16134574 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 25.06.2023. Verfasst von Jelena R Stojković und 7 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Mechanical Engineering, University of Niš, Aleksandra Medvedeva 14, 18000 Niš, Serbia. Die Arbeit wurde bisher 111-mal zitiert (Crossref) und nennt 65 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: EEA and Norway Grants, Ministry of Science, Technological Development and Innovation of the Republic of Serbia, EEA & Norway Grant.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study investigates the impact of annealing time, temperature, and layer height on the tensile strength and dimensional change of three 3D printing materials (PLA, PETG, and carbon fiber-reinforced PETG). Samples with varying layer heights (0.1 mm, 0.2 mm, and 0.3 mm) were annealed at temperatures ranging from 60–100 °C for 30, 60, and 90 min. Tensile tests were conducted, and regression models were developed to analyze the effects of these parameters on tensile strength. The models exhibited high accuracy, with a maximum deviation of only 5% from measured validation values. The models showed that layer height has a significantly bigger influence on tensile strength than annealing time and temperature. Optimal combinations of parameters were identified for each material, with PLA performing best at 0.1 mm/60 min/90 °C and PETG and PETGCF achieving optimal tensile strength at 0.1 mm/90 min/60 °C. PETGCF demonstrated smallest dimensional change after annealing and had the best modulus of elasticity of all the materials. The study employed experimental testing and regression models to assess the results across multiple materials under consistent conditions, contributing valuable insights to the ongoing discussion on the influence of annealing in 3D-printed parts.

Schlagwörter

Stichwörter der Autor:innen

PETGPETGCFPLAannealinglayer thicknessmechanical testingregression model

Autor:innen und Institutionen

  • Faculty of Mechanical Engineering, University of Niš, Aleksandra Medvedeva 14, 18000 Niš, Serbia.
  • Faculty of Mechanical Engineering, Poznan University of Technology, Piotrowo 3 STR, 61-138 Poznan, Poland.
  • Department of Manufacturing Engineering, Faculty of Industrial Engineering, Robotics and Production Management, Technical University of Cluj-Napoca, Blv. Muncii, No. 103-105, 400641 Cluj-Napoca, Romania.
  • Department of Mechatronics and Machine Dynamics, Faculty of Automotive, Mechatronics and Mechanical Engineering, Technical University of Cluj-Napoca, Blv. Muncii, No. 103-105, 400641 Cluj-Napoca, Romania.

ORCID-Profile: Jelena R Stojković, Alexandru Ianoşi-Andreeva-Dimitrova, Răzvan Păcurar

Förderung

  • EEA and Norway Grants
  • Ministry of Science, Technological Development and Innovation of the Republic of Serbia
  • EEA & Norway Grant
  • EMERALD

Zitieren

APA

Stojković, J. R., Turudija, R., Vitković, N., Górski, F., Păcurar, A., Pleşa, A., Ianoşi-Andreeva-Dimitrova, A., & Păcurar, R. (2023). An Experimental Study on the Impact of Layer Height and Annealing Parameters on the Tensile Strength and Dimensional Accuracy of FDM 3D Printed Parts. Materials, 16(13), 4574. https://doi.org/10.3390/ma16134574

Vancouver

Stojković JR, Turudija R, Vitković N, Górski F, Păcurar A, Pleşa A, et al. An Experimental Study on the Impact of Layer Height and Annealing Parameters on the Tensile Strength and Dimensional Accuracy of FDM 3D Printed Parts. Materials. 2023;16(13):4574. doi:10.3390/ma16134574

BibTeX
@article{Stojkovi2023,
  author = {Stojković, Jelena R and Turudija, Rajko and Vitković, Nikola and Górski, Filip and Păcurar, Ancuţa and Pleşa, Alin and Ianoşi-Andreeva-Dimitrova, Alexandru and Păcurar, Răzvan},
  title = {An Experimental Study on the Impact of Layer Height and Annealing Parameters on the Tensile Strength and Dimensional Accuracy of FDM 3D Printed Parts},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {13},
  pages = {4574},
  doi = {10.3390/ma16134574}
}
Kostenlos starten →