EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Experimental Study of In-Process Heat Treatment on the Mechanical Properties of 3D Printed Thermoplastic Polymer PLA

Ioan Tamașag iD, Irina Beșliu-Băncescu iD, Traian-Lucian Severin iD, Constantin Dulucheanu iD, Delia-Aurora Cerlincă iD

Polymers · 18.05.2023 · 15 (10) · 2367

DOI: 10.3390/polym15102367 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 18.05.2023. Verfasst von Ioan Tamașag und 4 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Mechanical Engineering, Automotive and Robotics, Stefan cel Mare University, 720229 Suceava, Romania. Die Arbeit wurde bisher 25-mal zitiert (Crossref) und nennt 48 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Human Capital Operational Programme 2014–2020 (POCU), Romania.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The scientific literature regarding additive manufacturing, mainly the material extrusion method, suggests that the mechanical characteristics of the parts obtained by this technology depend on a number of the input factors specific to the printing process, such as printing temperature, printing trajectory, layer height, etc., and also on the post-process operations for parts, which, unfortunately, requires supplementary setups, equipment, and multiple steps that raise the overall costs. Therefore, this paper aims to investigate the influence of the printing direction, the thickness of the deposited material layer, and the temperature of the previously deposited material layer on the part tensile strength, hardness by means of Shore D and Martens hardness, and surface finish by using an in-process annealing method. A Taguchi L9 DOE plan was developed for this purpose, where the test specimens, with dimensions according to ISO 527-2 type B, were analysed. The results showed that the presented in-process treatment method is possible and could lead to sustainable and cost-effective manufacturing processes. The varied input factors influenced all the studied parameters. Tensile strength tended to increase, up to 12.5%, when the in-process heat treatment was applied, showed a positive linear variation with nozzle diameter, and presented considerable variations with the printing direction. Shore D and Martens hardness had similar variations, and it could be observed that by applying the mentioned in-process heat treatment, the overall values tended to decrease. Printing direction had a negligible impact on the additively manufactured parts’ hardness. At the same time, the nozzle diameter presented considerable variations, up to 36% for Martens hardness and 4% for Shore D, when higher diameter nozzles were used. The ANOVA analysis highlighted that the statistically significant factors were the nozzle diameter for the part’s hardness and the printing direction for the tensile strength.

Schlagwörter

Stichwörter der Autor:innen

PLAadditive manufacturingannealingmechanical proprietiessurface quality

Autor:innen und Institutionen

  • Faculty of Mechanical Engineering, Automotive and Robotics, Stefan cel Mare University, 720229 Suceava, Romania.

ORCID-Profile: Ioan Tamașag, Irina Beșliu-Băncescu, Traian-Lucian Severin, Constantin Dulucheanu, Delia-Aurora Cerlincă

Förderung

  • Human Capital Operational Programme 2014–2020 (POCU), Romania

Zitieren

APA

Tamașag, I., Beșliu-Băncescu, I., Severin, T. L., Dulucheanu, C., & Cerlincă, D. A. (2023). Experimental Study of In-Process Heat Treatment on the Mechanical Properties of 3D Printed Thermoplastic Polymer PLA. Polymers, 15(10), 2367. https://doi.org/10.3390/polym15102367

Vancouver

Tamașag I, Beșliu-Băncescu I, Severin TL, Dulucheanu C, Cerlincă DA. Experimental Study of In-Process Heat Treatment on the Mechanical Properties of 3D Printed Thermoplastic Polymer PLA. Polymers. 2023;15(10):2367. doi:10.3390/polym15102367

BibTeX
@article{Tamaag2023,
  author = {Tamașag, Ioan and Beșliu-Băncescu, Irina and Severin, Traian-Lucian and Dulucheanu, Constantin and Cerlincă, Delia-Aurora},
  title = {Experimental Study of In-Process Heat Treatment on the Mechanical Properties of 3D Printed Thermoplastic Polymer PLA},
  journal = {Polymers},
  year = {2023},
  volume = {15},
  number = {10},
  pages = {2367},
  doi = {10.3390/polym15102367}
}
Kostenlos starten →