The Effect of Heat Treatment on a 3D-Printed PLA Polymer’s Mechanical Properties
Polymers · 22.03.2023 · 15 (6) · 1587
DOI: 10.3390/polym15061587 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 22.03.2023. Verfasst von Mariam Shbanah und 4 weiteren Autor:innen. Beteiligte Einrichtung: Doctoral School on Materials Sciences and Technologies, Óbuda University, Bécsi út 96/B, 1034 Budapest, Hungary. Die Arbeit wurde bisher 63-mal zitiert (Crossref) und nennt 32 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Óbuda University.
Abstract (Originalsprache)
Three-dimensional printing is a useful and common process in additive manufacturing nowadays. The advantage of additive polymer technology is its rapidity and design freedom. Polymer materials’ mechanical properties depend on the process parameters and the chemical composition of the polymer used. Mechanical properties are very important in product applicability. The mechanical properties of polymers can be enhanced by heat treatment. Additive-manufactured PLA’s mechanical properties and structure can be modified via heat treatment after the 3D printing process. The goal of this research was to test the effect of heat treatment on the mechanical and structural parameters of additive-manufactured PLA. This was achieved via the FDM processing of standard PLA tensile test specimens with longitudinal and vertical printing orientations. After printing, the test specimens were heat-treated at 55 °C, 65 °C and 80 °C for 5 h and after being held at 20 °C for 15 h. The printed and heat-treated specimens were tested using tensile tests and microscopy. Based on the test results, we can conclude that the optimal heat treatment process temperature was 65 °C for 5 h. Under the heat treatment, the test specimens did not show any deformation, the tensile strength increased by 35% and the porosity of the PLA structure decreased.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Doctoral School on Materials Sciences and Technologies, Óbuda University, Bécsi út 96/B, 1034 Budapest, Hungary.
- Bánki Donát Faculty of Mechanical and Safety Engineering, Óbuda University, Népszínház u. 8., 1081 Budapest, Hungary.
- Department of Informatics, Milton Friedman University, Kelta u. 2., 1039 Budapest, Hungary.
ORCID-Profile: Márton Jordanov, László Tóth, Tünde Anna Kovács
Förderung
- Óbuda University
Zitieren
APA
Shbanah, M., Jordanov, M., Nyikes, Z., Tóth, L., & Kovács, T. A. (2023). The Effect of Heat Treatment on a 3D-Printed PLA Polymer’s Mechanical Properties. Polymers, 15(6), 1587. https://doi.org/10.3390/polym15061587
Vancouver
Shbanah M, Jordanov M, Nyikes Z, Tóth L, Kovács TA. The Effect of Heat Treatment on a 3D-Printed PLA Polymer’s Mechanical Properties. Polymers. 2023;15(6):1587. doi:10.3390/polym15061587
BibTeX
@article{Shbanah2023,
author = {Shbanah, Mariam and Jordanov, Márton and Nyikes, Zoltán and Tóth, László and Kovács, Tünde Anna},
title = {The Effect of Heat Treatment on a 3D-Printed PLA Polymer’s Mechanical Properties},
journal = {Polymers},
year = {2023},
volume = {15},
number = {6},
pages = {1587},
doi = {10.3390/polym15061587}
}
EUVIMED