EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of Atmospheric Plasma Treatment on Mechanical Properties of 3D-Printed Continuous Aramid Fiber/PLA Composites

Fidan Bilir Kilinc iD, Ebru Bozaci iD, Ahmet Cagri Kilinc iD, Turker Turkoglu iD

Polymers · 01.02.2025 · 17 (3) · 397

DOI: 10.3390/polym17030397 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 01.02.2025. Verfasst von Fidan Bilir Kilinc und 3 weiteren Autor:innen. Beteiligte Einrichtung: Graduate School of Natural and Applied Sciences, Department of Textile Engineering, Ege University, 35100 Izmir, Turkey. Die Arbeit wurde bisher 21-mal zitiert (Crossref) und nennt 43 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In this study, an aluminum heating block with two inlets (for the Polylactic acid (PLA) filament and the continuous aramid fiber) was produced and placed onto an extruder, and continuous-aramid-fiber-reinforced PLA composites were fabricated by using the nozzle impregnation method. Layer height values of 0.4 mm, 0.6 mm, and 0.8 mm and hatch spacing values of 0.6 mm, 0.8 mm, and 1.0 mm were used for the investigation of the processing parameters on the properties of composites by differentiating the reinforcement volume fraction. Additionally, atmospheric plasma treatment was used for the surface modification of the reinforcement fiber. The properties of composites reinforced by using surface-modified fibers were also investigated in order to reveal the efficacy of the atmospheric plasma treatment on the properties of composites. The effect of the atmospheric plasma treatment on the fiber properties was investigated by using scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FT-IR), and X-ray photoelectron spectroscopy (XPS). Continuous-aramid-fiber-reinforced PLA composites were characterized mechanically by fiber pull-out, tensile, and flexural testing. The fracture surfaces of composites were analyzed by using SEM. The combination of a reduced layer height and a narrower hatch spacing yielded the best mechanical performance, with a tensile strength of 410.25 MPa achieved at a 0.6 mm layer height and a 0.4 mm hatch spacing. This combination minimizes void formation, enhances fiber alignment, and strengthens interlayer adhesion, leading to superior mechanical properties. The FTIR and XPS results showed that atmospheric plasma modification can enhance the interfacial bonding strength by improving the surface morphology and increasing the content of polar groups on the fiber surface. By combining optimized manufacturing conditions with the atmospheric plasma treatment, the mechanical performance of continuous-aramid-fiber-reinforced PLA composites was enhanced.

Schlagwörter

Stichwörter der Autor:innen

3D printingFDMaramidatmospheric plasma treatmentcompositecontinuous fiber

Autor:innen und Institutionen

  • Graduate School of Natural and Applied Sciences, Department of Textile Engineering, Ege University, 35100 Izmir, Turkey.
  • Department of Textile Engineering, Ege University, 35100 Izmir, Turkey.
  • Department of Mechanical Engineering, Osmaniye Korkut Ata University, 80010 Osmaniye, Turkey.
  • Department of Mechanical Engineering, Balıkesir University, 10100 Balıkesir, Turkey.

ORCID-Profile: Fidan Bilir Kilinc, Ebru Bozaci, Ahmet Cagri Kilinc, Turker Turkoglu

Zitieren

APA

Kilinc, F. B., Bozaci, E., Kilinc, A. C., & Turkoglu, T. (2025). Effect of Atmospheric Plasma Treatment on Mechanical Properties of 3D-Printed Continuous Aramid Fiber/PLA Composites. Polymers, 17(3), 397. https://doi.org/10.3390/polym17030397

Vancouver

Kilinc FB, Bozaci E, Kilinc AC, Turkoglu T. Effect of Atmospheric Plasma Treatment on Mechanical Properties of 3D-Printed Continuous Aramid Fiber/PLA Composites. Polymers. 2025;17(3):397. doi:10.3390/polym17030397

BibTeX
@article{Kilinc2025,
  author = {Kilinc, Fidan Bilir and Bozaci, Ebru and Kilinc, Ahmet Cagri and Turkoglu, Turker},
  title = {Effect of Atmospheric Plasma Treatment on Mechanical Properties of 3D-Printed Continuous Aramid Fiber/PLA Composites},
  journal = {Polymers},
  year = {2025},
  volume = {17},
  number = {3},
  pages = {397},
  doi = {10.3390/polym17030397}
}
Kostenlos starten →