EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Time-Dependent Effects of 222 nm UVC Photofunctionalization on Dentin Adhesion to CAD/CAM Resin Blocks

Yutaka Ishikawa, Yukitoshi Kurakawa, Yousuke Yamazaki

Oral · 17.08.2026 · 6 (4) · 107

DOI: 10.3390/oral6040107 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Oral, online erschienen am 17.08.2026. Verfasst von Yutaka Ishikawa und 2 weiteren Autor:innen. Die Arbeit nennt 26 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Background/Objectives: This study aimed to investigate the effect of UVC irradiation on the adhesive strength between a CAD/CAM composite resin block and dentin and to apply UVC to dental care.

Methods

CAD/CAM composite resin blocks were sectioned, polished, and primed using a ceramic primer. Bovine dentin specimens were prepared and irradiated with 222 nm UVC light for no time (control, no UV), 600 s or 1200 s. After irradiation, dentin surfaces were conditioned with a tooth primer before bonding with a resin cement. Microtensile bond strength (μTBS) testing, scanning electron microscope (SEM)-based failure mode analysis, and contact angle measurements were conducted.

Results

The control measured 34.32 (±3.11) MPa, the 600 s group measured 42.64 (±4.50) MPa, and the 1200 s group measured 39.75 (±7.52) MPa. There were no significant differences observed in the 1200 s group when compared with the control group. Conversely, a remarkable increase in adhesive strength was observed in the 600 s group in comparison to the control group. Failure mode analysis revealed a predominance of mixed failures in the 600 s group, which suggests enhanced interfacial bonding. Contact angle measurements demonstrated significantly enhanced surface wettability in both UVC irradiation groups relative to the control (p < 0.05).

Conclusions

Photofunctionalization with 222 nm UVC improved dentin adhesion to CAD/CAM resin blocks, likely through enhanced hydrophilicity and removal of organic contaminants. Nonetheless, extended irradiation did not produce additional benefits, indicating a time-dependent response. Although 222 nm UVC irradiation demonstrates promise as a pretreatment approach in adhesive dentistry, further optimization is necessary to shorten irradiation duration and improve clinical feasibility.

Zitieren

APA

Ishikawa, Y., Kurakawa, Y., & Yamazaki, Y. (2026). Time-Dependent Effects of 222 nm UVC Photofunctionalization on Dentin Adhesion to CAD/CAM Resin Blocks. Oral, 6(4), 107. https://doi.org/10.3390/oral6040107

Vancouver

Ishikawa Y, Kurakawa Y, Yamazaki Y. Time-Dependent Effects of 222 nm UVC Photofunctionalization on Dentin Adhesion to CAD/CAM Resin Blocks. Oral. 2026;6(4):107. doi:10.3390/oral6040107

BibTeX
@article{Ishikawa2026,
  author = {Ishikawa, Yutaka and Kurakawa, Yukitoshi and Yamazaki, Yousuke},
  title = {Time-Dependent Effects of 222 nm UVC Photofunctionalization on Dentin Adhesion to CAD/CAM Resin Blocks},
  journal = {Oral},
  year = {2026},
  volume = {6},
  number = {4},
  pages = {107},
  doi = {10.3390/oral6040107}
}
Kostenlos starten →