EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Size-Dependent Strength and Reliability of Resin Composite Blocks and Nanoceramics for Computer-Aided Design/Computer-Aided Manufacturing (CAD/CAM) Restorations

Fernando Ledesma-Renedo iD, Eva Paz, Francisco Martínez-Rus iD, Miguel Ángel Rodríguez-Pérez iD, Guillermo Pradíes iD

Materials · 13.06.2026 · 19 (12) · 2564

DOI: 10.3390/ma19122564 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 13.06.2026. Verfasst von Fernando Ledesma-Renedo und 4 weiteren Autor:innen. Beteiligte Einrichtung: Analysis of Techniques, Material and Instruments Applied to Digital Dentistry and CAD/CAM Procedures Research Group, Department of Conservative and P…. Die Arbeit nennt 45 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Background

Mechanical reliability and size-dependent strength behavior remain critical concerns for CAD/CAM restorative materials. This study evaluated resin-based CAD/CAM materials, including resin composite blocks (RCBs) and nanoceramics. The influence of specimen size on flexural strength and the applicability of Weibull-based strength predictions were assessed by comparing experimental and Weibull-predicted values.

Methods

Twelve CAD/CAM materials were investigated, including ten resin-based materials and two controls (lithium disilicate ceramic and polymethyl methacrylate). Rectangular specimens (1 × 4 × 14 mm and 1 × 12 × 14 mm) were tested using a three-point bending test. Flexural strength, modulus, and resilience were calculated. Reliability and size dependence were assessed using two-parameter Weibull statistics and effective-volume-based predictions. Data were analyzed using statistical tests selected according to data distribution characteristics (α = 0.05).

Results

RCBs exhibited higher flexural strength, modulus, and resilience than nanoceramics (p < 0.05). Weibull analysis indicated higher reliability and limited size dependence for RCBs, whereas nanoceramics showed greater variability. The ceramic control exhibited the expected reduction in strength with increasing specimen size. In contrast, resin-based materials showed inconsistent responses to changes in specimen size. Prediction error analysis revealed variable agreement between predicted and experimental values, indicating that agreement with classical Weibull assumptions was material-dependent.

Conclusions

Resin-based CAD/CAM materials demonstrated limited size-dependent behavior compared with brittle ceramics. The reduced agreement between experimental and Weibull-predicted values suggests that effective-volume scaling may have limited applicability for these contemporary materials and should be interpreted cautiously on a material-specific basis.

Schlagwörter

Stichwörter der Autor:innen

ceramicscomposite resinscomputer-aided designdental materialsflexural strength

Autor:innen und Institutionen

  • Analysis of Techniques, Material and Instruments Applied to Digital Dentistry and CAD/CAM Procedures Research Group, Department of Conservative and Prosthetic Dentistry, Faculty of Odontology, Complutense University of…
  • Institute for Research in Technology (IIT), Mechanical Engineering Department, ICAI School of Engineering, Comillas Pontifical University of Madrid, 28015 Madrid, Spain.
  • Cellular Materials Laboratory (CellMat), Condensed Matter Physics Department, Campus Miguel Delibes Science Faculty, University of Valladolid, 47011 Valladolid, Spain.

ORCID-Profile: Fernando Ledesma-Renedo, Francisco Martínez-Rus, Miguel Ángel Rodríguez-Pérez, Guillermo Pradíes

Zitieren

APA

Ledesma-Renedo, F., Paz, E., Martínez-Rus, F., Rodríguez-Pérez, M. Á., & Pradíes, G. (2026). Size-Dependent Strength and Reliability of Resin Composite Blocks and Nanoceramics for Computer-Aided Design/Computer-Aided Manufacturing (CAD/CAM) Restorations. Materials, 19(12), 2564. https://doi.org/10.3390/ma19122564

Vancouver

Ledesma-Renedo F, Paz E, Martínez-Rus F, Rodríguez-Pérez MÁ, Pradíes G. Size-Dependent Strength and Reliability of Resin Composite Blocks and Nanoceramics for Computer-Aided Design/Computer-Aided Manufacturing (CAD/CAM) Restorations. Materials. 2026;19(12):2564. doi:10.3390/ma19122564

BibTeX
@article{LedesmaRenedo2026,
  author = {Ledesma-Renedo, Fernando and Paz, Eva and Martínez-Rus, Francisco and Rodríguez-Pérez, Miguel Ángel and Pradíes, Guillermo},
  title = {Size-Dependent Strength and Reliability of Resin Composite Blocks and Nanoceramics for Computer-Aided Design/Computer-Aided Manufacturing (CAD/CAM) Restorations},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {12},
  pages = {2564},
  doi = {10.3390/ma19122564}
}
Kostenlos starten →