EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of Preparation Conditions of Fe@SiO2 Catalyst on Its Structure Using High-Pressure Activity Studies in a 3D-Printed SS Microreactor

Meric Arslan, Sujoy Bepari iD, Juvairia Shajahan, Saif Hassan, Debasish Kuila

Molecules · 13.01.2025 · 30 (2) · 280

DOI: 10.3390/molecules30020280 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Molecules, online erschienen am 13.01.2025. Verfasst von Meric Arslan und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Applied Science and Technology, North Carolina Agricultural and Technical State University, Greensboro, NC 27411, USA. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 76 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Science Foundation, UNC-ROI, NSF-SENIC.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Fischer–Tropsch synthesis (FTS) in a 3D-printed stainless steel (SS) microchannel microreactor was investigated using Fe@SiO2 catalysts. The catalysts were prepared by two different techniques: one pot (OP) and autoclave (AC). The mesoporous structure of the two catalysts, Fe@SiO2 (OP) and Fe@SiO2 (AC), ensured a large contact area between the reactants and the catalyst. They were characterized by N2 physisorption, H2 temperature-programmed reduction (H2-TPR), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), X-ray photoelectron microscopy (XPS), and thermogravimetric analysis–differential scanning calorimetry (TGA-DSC) techniques. The AC catalyst had a clear core–shell structure and showed a much greater surface area than that prepared by the OP method. The activities of the catalysts in terms of FTS were studied in the 200–350 °C temperature range at 20-bar pressure with a H2/CO molar ratio of 2:1. The Fe@SiO2 (AC) catalyst showed higher selectivity and higher CO conversion to olefins than Fe@SiO2 (OP). Stability studies of both catalysts were carried out for 30 h at 320 °C at 20 bar with a feed gas molar ratio of 2:1. The Fe@SiO2 (AC) catalyst showed higher stability and yielded consistent CO conversion compared to the Fe@SiO2 (OP) catalyst.

Schlagwörter

Stichwörter der Autor:innen

FTSSS microreactorcore–shell Fe catalystmesoporous composite oxide

Autor:innen und Institutionen

  • Department of Applied Science and Technology, North Carolina Agricultural and Technical State University, Greensboro, NC 27411, USA.
  • Department of Chemistry, North Carolina Agricultural and Technical State University, Greensboro, NC 27411, USA.
  • Joint School of Nanoscience and Nanoengineering, North Carolina Agricultural and Technical State University, Greensboro, NC 27411, USA.

ORCID-Profile: Sujoy Bepari

Förderung

  • National Science Foundation
  • UNC-ROI
  • NSF-SENIC
  • DOE-BES
  • NSF-CREST

Zitieren

APA

Arslan, M., Bepari, S., Shajahan, J., Hassan, S., & Kuila, D. (2025). Effect of Preparation Conditions of Fe@SiO2 Catalyst on Its Structure Using High-Pressure Activity Studies in a 3D-Printed SS Microreactor. Molecules, 30(2), 280. https://doi.org/10.3390/molecules30020280

Vancouver

Arslan M, Bepari S, Shajahan J, Hassan S, Kuila D. Effect of Preparation Conditions of Fe@SiO2 Catalyst on Its Structure Using High-Pressure Activity Studies in a 3D-Printed SS Microreactor. Molecules. 2025;30(2):280. doi:10.3390/molecules30020280

BibTeX
@article{Arslan2025,
  author = {Arslan, Meric and Bepari, Sujoy and Shajahan, Juvairia and Hassan, Saif and Kuila, Debasish},
  title = {Effect of Preparation Conditions of Fe@SiO2 Catalyst on Its Structure Using High-Pressure Activity Studies in a 3D-Printed SS Microreactor},
  journal = {Molecules},
  year = {2025},
  volume = {30},
  number = {2},
  pages = {280},
  doi = {10.3390/molecules30020280}
}
Kostenlos starten →