EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

High-Power Femtosecond Laser Processing of SiC Ceramics with Optimized Material Removal Rate

Jian Zhang iD, Zhichao Liu, Yuanhang Zhang, Feng Geng, Shengfei Wang, Fei Fan, Qinghua Zhang, Qiao Xu

Micromachines · 21.10.2023 · 14 (10) · 1960

DOI: 10.3390/mi14101960 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Micromachines, online erschienen am 21.10.2023. Verfasst von Jian Zhang und 7 weiteren Autor:innen. Beteiligte Einrichtung: Laser Fusion Research Center, China Academy of Engineering Physics, Mianyang 621900, China. Die Arbeit wurde bisher 12-mal zitiert (Crossref) und nennt 34 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Natural Science Foundation of China, Natural Science Foundation of Sichuan Province.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Silicon carbide (SiC) ceramics are widely used as structural materials for various applications. However, the extraordinarily high hardness, brittleness, low material removal rate, and severe tool wear of these materials significantly impact the performance of conventional mechanical processing techniques. In this study, we investigated the influence of different parameters on the material removal rate, surface quality, and surface oxidation during the laser processing of SiC ceramic samples using a high-repetition-frequency femtosecond laser at a wavelength of 1030 nm. Additionally, an experimental investigation was conducted to analyze the effects of a burst mode on the material removal rate. Our results demonstrate that the surface oxidation, which significantly affects the material removal rate, can be effectively reduced by increasing the laser scanning speed and decreasing the laser scanning pitch. The material removal rate and surface quality are mainly affected by laser fluence. The optimal material removal rate is obtained with a laser fluence of 0.4 J/cm2 at a pulse width of 470 fs.

Schlagwörter

Stichwörter der Autor:innen

SiC ceramicsfemtosecond laserlaser processingmaterial removal ratesurface oxidation

Autor:innen und Institutionen

  • Laser Fusion Research Center, China Academy of Engineering Physics, Mianyang 621900, China.

ORCID-Profile: Jian Zhang

Förderung

  • National Natural Science Foundation of China
  • Natural Science Foundation of Sichuan Province

Zitieren

APA

Zhang, J., Liu, Z., Zhang, Y., Geng, F., Wang, S., Fan, F., Zhang, Q., & Xu, Q. (2023). High-Power Femtosecond Laser Processing of SiC Ceramics with Optimized Material Removal Rate. Micromachines, 14(10), 1960. https://doi.org/10.3390/mi14101960

Vancouver

Zhang J, Liu Z, Zhang Y, Geng F, Wang S, Fan F, et al. High-Power Femtosecond Laser Processing of SiC Ceramics with Optimized Material Removal Rate. Micromachines. 2023;14(10):1960. doi:10.3390/mi14101960

BibTeX
@article{Zhang2023,
  author = {Zhang, Jian and Liu, Zhichao and Zhang, Yuanhang and Geng, Feng and Wang, Shengfei and Fan, Fei and Zhang, Qinghua and Xu, Qiao},
  title = {High-Power Femtosecond Laser Processing of SiC Ceramics with Optimized Material Removal Rate},
  journal = {Micromachines},
  year = {2023},
  volume = {14},
  number = {10},
  pages = {1960},
  doi = {10.3390/mi14101960}
}
Kostenlos starten →