EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Impact of Heat Treatment and Building Direction on Tensile Properties and Fracture Mechanism of Inconel 718 Produced by SLM Process

Seokha Heo, Yujin Lim, Nawon Kwak, Chami Jeon, Moonhee Choi, Ilguk Jo

Metals · 10.04.2024 · 14 (4) · 440

DOI: 10.3390/met14040440 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Metals, online erschienen am 10.04.2024. Verfasst von Seokha Heo und 5 weiteren Autor:innen. Die Arbeit wurde bisher 40-mal zitiert (Crossref) und nennt 37 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Research Foundation of Korea (NRF), Korea Institute for Advancement of Technology (KIAT).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In the selective laser melting (SLM) additive manufacturing process of Inconel 718, the emergence of Laves and δ precipitate phases in the γ matrix during or after heat treatment is a critical consideration. This study comprehensively assesses the microstructures and mechanical properties of Inconel 718 alloy produced through SLM under varied conditions: as-built (AB), homogenization + solution + aging (HSA), homogenization + aging (HA), and solution + aging (SA). Additionally, the impact of building orientation, whether horizontal (H) or vertical (V), is investigated. The AB specimens oriented horizontally display a columnar melt pool structure, with dimensions roughly between 300 and 400 μm. In contrast, the AB specimens aligned vertically show an elongated river-like structure of melt pools, with their sizes approximately at 250 μm. From the detailed microstructural analysis, the findings reveal that the as-built specimens lack γ′ and γ″ precipitates in their microstructure. Conversely, in heat-treated specimens, both the γ′ and γ″ phases are evident. Notably, Inconel 718 alloy specimens subjected to SLM fabrication and SA heat treatment demonstrate optimal mechanical performance. Notably, SA exhibits an average hardness of 476 HV for the horizontal specimen, which is 51.1% higher than that of AB specimens. The morphology and distribution of the δ phase in the γ matrix emerge as decisive factors influencing high-temperature performance. In SA specimens, the dissolution of brittle Laves phases occurs, and the presence of the δ phase at the grain boundary imparts superior properties during high-temperature tensile testing, including excellent yield and ultimate tensile strength. The presence of the granular-δ phase in the SA specimens resulted in a tensile strength of 1422 MPa and a yield strength of 1236 MPa, which are the highest values among all the specimens. SA has a tensile strength of 1120 MPa and a yield strength of 974 MPa at 650 °C.

Förderung

  • National Research Foundation of Korea (NRF)
  • Korea Institute for Advancement of Technology (KIAT)

Zitieren

APA

Heo, S., Lim, Y., Kwak, N., Jeon, C., Choi, M., & Jo, I. (2024). Impact of Heat Treatment and Building Direction on Tensile Properties and Fracture Mechanism of Inconel 718 Produced by SLM Process. Metals, 14(4), 440. https://doi.org/10.3390/met14040440

Vancouver

Heo S, Lim Y, Kwak N, Jeon C, Choi M, Jo I. Impact of Heat Treatment and Building Direction on Tensile Properties and Fracture Mechanism of Inconel 718 Produced by SLM Process. Metals. 2024;14(4):440. doi:10.3390/met14040440

BibTeX
@article{Heo2024,
  author = {Heo, Seokha and Lim, Yujin and Kwak, Nawon and Jeon, Chami and Choi, Moonhee and Jo, Ilguk},
  title = {Impact of Heat Treatment and Building Direction on Tensile Properties and Fracture Mechanism of Inconel 718 Produced by SLM Process},
  journal = {Metals},
  year = {2024},
  volume = {14},
  number = {4},
  pages = {440},
  doi = {10.3390/met14040440}
}
Kostenlos starten →