EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Macrohardness-Based Spatial Homogeneity Analysis of TIG-Welded AISI 304 Stainless Steel

Saulius Baskutis iD, Yaroslav Kusyi iD, Lina Kavaliauskiene iD, Jolanta Baskutiene iD, Tomas Kačinskas iD, Oleh Onysko iD

Materials · 05.11.2026 · 19 (21) · 4708

DOI: 10.3390/ma19214708 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 05.11.2026. Verfasst von Saulius Baskutis und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Production Engineering, Faculty of Mechanical Engineering and Design, Kaunas University of Technology, Studentu St. 56, 51424 Kaunas, L…. Die Arbeit nennt 56 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study evaluates a material homogeneity criterion (MHC)-based workflow for the spatial characterization of macrohardness variability in tungsten inert gas (TIG) welded AISI 304 stainless-steel joints produced using 308LSi filler metal. Five welded specimens produced under different welding conditions were first evaluated by transverse tensile testing. Two specimens representing contrasting mechanical responses were subsequently selected for identical spatial macrohardness mapping: Specimen 1 exhibited the lowest ultimate tensile strength (610 MPa), 24% elongation, and fracture through the weld region, whereas Specimen 3 exhibited the highest ultimate tensile strength (684 MPa), 41% elongation, and fracture in the base material. For each specimen, 1000 Rockwell macrohardness (HRBW) measurements were obtained along twenty transverse measurement lines spanning the base material (BM), heat-affected zone (HAZ), and fusion zone (FZ). Mean hardness ranges were comparatively similar for Specimens 1 and 3 (92.04–95.70 and 92.00–95.50 HRBW, respectively). Meanwhile, the coefficient of variation (CV) and Weibull homogeneity coefficient (WHC) provided greater discrimination between the two joints. Specimen 1 exhibited CV values of 0.534–1.433% and WHC values of 81.20–216.95, whereas Specimen 3 exhibited CV values of 0.542–1.076% and WHC values of 107.87–214.12. The largest between-specimen difference was observed within the HAZ, where Specimen 1 exhibited substantially greater macrohardness dispersion than Specimen 3. These results show that statistical treatment of repeated macrohardness measurements can reveal spatial differences between welded joints that are less evident from mean-hardness profiles alone. The comparison does not establish a general predictive relationship between hardness dispersion and tensile performance but provides experimental evidence supporting the discriminatory value of spatial CV and WHC mapping for the two investigated contrasting cases. Optical metallography provides complementary qualitative microstructural characterization, while quantitative relationships between microstructural parameters and macrohardness dispersion remain outside the scope of the present study.

Schlagwörter

Stichwörter der Autor:innen

AISI 304 stainless steelTIG weldingWeibull homogeneity coefficientcoefficient of variationmacrohardnessmaterial homogeneity criterion

Autor:innen und Institutionen

  • Department of Production Engineering, Faculty of Mechanical Engineering and Design, Kaunas University of Technology, Studentu St. 56, 51424 Kaunas, Lithuania.
  • Department of Robotics and Integrated Mechanical Engineering Technologies, Lviv Polytechnic National University, Bandera St. 12, 79013 Lviv, Ukraine.
  • Department of Computerized Mechanical Engineering, Ivano-Frankivsk National Technical University of Oil and Gas, Karpatska St. 15, 76000 Ivano-Frankivsk, Ukraine.

ORCID-Profile: Saulius Baskutis, Yaroslav Kusyi, Lina Kavaliauskiene, Jolanta Baskutiene, Tomas Kačinskas, Oleh Onysko

Zitieren

APA

Baskutis, S., Kusyi, Y., Kavaliauskiene, L., Baskutiene, J., Kačinskas, T., & Onysko, O. (2026). Macrohardness-Based Spatial Homogeneity Analysis of TIG-Welded AISI 304 Stainless Steel. Materials, 19(21), 4708. https://doi.org/10.3390/ma19214708

Vancouver

Baskutis S, Kusyi Y, Kavaliauskiene L, Baskutiene J, Kačinskas T, Onysko O. Macrohardness-Based Spatial Homogeneity Analysis of TIG-Welded AISI 304 Stainless Steel. Materials. 2026;19(21):4708. doi:10.3390/ma19214708

BibTeX
@article{Baskutis2026,
  author = {Baskutis, Saulius and Kusyi, Yaroslav and Kavaliauskiene, Lina and Baskutiene, Jolanta and Kačinskas, Tomas and Onysko, Oleh},
  title = {Macrohardness-Based Spatial Homogeneity Analysis of TIG-Welded AISI 304 Stainless Steel},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {21},
  pages = {4708},
  doi = {10.3390/ma19214708}
}
Kostenlos starten →