Effect of Embossing Pattern Geometry on the Tensile Strength of Three-Layer Films Containing Recycled Polyethylene
Materials · 01.11.2026 · 19 (21) · 4657
DOI: 10.3390/ma19214657 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 01.11.2026. Verfasst von Jachowicz Tomasz und 6 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Mechanical Engineering, Lublin University of Technology, 38 Nadbystrzycka Str., 20-618 Lublin, Poland. Die Arbeit nennt 27 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Centre for Research and Development, Polipak sp. z o.o..
Abstract (Originalsprache)
This paper presents the results of experimental tests on the static tensile strength and relative elongation of three-layer films containing varying proportions of recycled polyethylene and subjected to an embossing process. Films containing varying proportions of recycled low-density and high-density polyethylene were produced by blown film extrusion. The embossing process was carried out under varying processing conditions, and embossing patterns with different geometrical characteristics were produced on the three-layer films under investigation. The films were manufactured and the experimental tests were conducted under industrial conditions. Based on the results obtained, the effects of three different embossing pattern geometries and the embossing process parameters on the tensile strength of three-layer films made from recycled polyethylene were evaluated in the machine and transverse directions. The experimental results enabled the identification of embossing pattern geometries and recycled polyethylene contents that increased static tensile strength in selected material–process combinations. No statistically significant improvement in elongation at break was confirmed compared with the non-embossed reference films. The findings are limited to static tensile strength and elongation at break in the machine direction (MD) and cross direction (CD), which contribute to improving certain functional properties of refuse bags, specifically ensuring adequate load-bearing capacity for the waste they contain.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Faculty of Mechanical Engineering, Lublin University of Technology, 38 Nadbystrzycka Str., 20-618 Lublin, Poland.
- Institute of Materials and Biomedical Engineering, University of Zielona Góra, 4 Prof. Z. Szafran Str., 65-516 Zielona Góra, Poland.
- Institute of Mechanical Engineering, University of Zielona Góra, 4 Prof. Z. Szafran Str., 65-516 Zielona Góra, Poland.
- Institute of Mathematics, University of Zielona Góra, 4 Prof. Z. Szafran Str., 65-516 Zielona Góra, Poland.
- Faculty of Control, Robotics and Electrical Engineering, Poznań University of Technology, 3A Piotrowo Str., 60-965 Poznań, Poland.
- Polipak sp. z o.o., Fabryczna 7, 63-000 Środa Wielkopolska, Poland.
ORCID-Profile: Jachowicz Tomasz, Jajczyk Jarosław, Arkadiusz Kozioł
Förderung
- National Centre for Research and Development
- Polipak sp. z o.o.
Zitieren
APA
Tomasz, J., Waldemar, W., Michał, S., Maciej, N., Jarosław, J., Kozioł, A., & Tramś, T. (2026). Effect of Embossing Pattern Geometry on the Tensile Strength of Three-Layer Films Containing Recycled Polyethylene. Materials, 19(21), 4657. https://doi.org/10.3390/ma19214657
Vancouver
Tomasz J, Waldemar W, Michał S, Maciej N, Jarosław J, Kozioł A, et al. Effect of Embossing Pattern Geometry on the Tensile Strength of Three-Layer Films Containing Recycled Polyethylene. Materials. 2026;19(21):4657. doi:10.3390/ma19214657
BibTeX
@article{Tomasz2026,
author = {Tomasz, Jachowicz and Waldemar, Woźniak and Michał, Sąsiadek and Maciej, Niedziela and Jarosław, Jajczyk and Kozioł, Arkadiusz and Tramś, Tomasz},
title = {Effect of Embossing Pattern Geometry on the Tensile Strength of Three-Layer Films Containing Recycled Polyethylene},
journal = {Materials},
year = {2026},
volume = {19},
number = {21},
pages = {4657},
doi = {10.3390/ma19214657}
}
EUVIMED