EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Research on the Microstructure and Mechanical Properties of Automatically Welded Martensitic Stainless Steel Joints for Thick Plates

Yunxia Chen iD, Yunwang Ding, Shanshan Lyu, Zesong Chen

Materials · 10.06.2026 · 19 (12) · 2507

DOI: 10.3390/ma19122507 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 10.06.2026. Verfasst von Yunxia Chen und 3 weiteren Autor:innen. Beteiligte Einrichtung: School of Intelligent Manufacturing and Control Engineering, Shanghai Polytechnic University, Shanghai 201209, China. Die Arbeit nennt 25 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

To address the performance degradation associated with retained high-temperature δ-ferrite in welded joints of high-silicon 20Cr11W2VTaSi steel—a candidate structural material for spallation targets in Accelerator Driven Subcritical Systems—this study systematically investigates the microstructural evolution and mechanical behavior of 20 mm-thick forged joints produced via automated tungsten inert gas (TIG) welding using a 7° U-groove narrow-gap configuration. Results demonstrate that the narrow-gap process—featuring reduced filler metal deposition and low heat input—is believed to suppress macrosegregation of ferrite-stabilizing elements (e.g., Cr, Si, Mo). As a result, the δ-ferrite content in the weld metal is constrained, exhibiting a fine, dispersed, worm-like morphology embedded within a uniform matrix of tempered martensite. Microhardness mapping confirms homogeneous hardness distribution across the joint, closely matching that of the base metal, with no statistically significant localized softening zones identified. Mechanical characterization reveals an optimal balance of strength and toughness: the joint achieves a room-temperature tensile strength of 820 MPa and retains 436 MPa at 550 °C; moreover, the Charpy impact energy at the weld center reaches 171.2 J.

Schlagwörter

Stichwörter der Autor:innen

20Cr11W2VTaSi martensitic heat-resistant steelhigh-temperature tensile strengthimpact toughnessnarrow-gap TIG weldingweld microstructure

Autor:innen und Institutionen

  • School of Intelligent Manufacturing and Control Engineering, Shanghai Polytechnic University, Shanghai 201209, China.
  • School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240, China.

ORCID-Profile: Yunxia Chen

Zitieren

APA

Chen, Y., Ding, Y., Lyu, S., & Chen, Z. (2026). Research on the Microstructure and Mechanical Properties of Automatically Welded Martensitic Stainless Steel Joints for Thick Plates. Materials, 19(12), 2507. https://doi.org/10.3390/ma19122507

Vancouver

Chen Y, Ding Y, Lyu S, Chen Z. Research on the Microstructure and Mechanical Properties of Automatically Welded Martensitic Stainless Steel Joints for Thick Plates. Materials. 2026;19(12):2507. doi:10.3390/ma19122507

BibTeX
@article{Chen2026,
  author = {Chen, Yunxia and Ding, Yunwang and Lyu, Shanshan and Chen, Zesong},
  title = {Research on the Microstructure and Mechanical Properties of Automatically Welded Martensitic Stainless Steel Joints for Thick Plates},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {12},
  pages = {2507},
  doi = {10.3390/ma19122507}
}
Kostenlos starten →