EUVIMEDOpdag EUVIMED
Open access · CC BY 4.0

Influence of Sintering and Heat Treatment on the Microstructure, Mechanical Properties, and Tribological Performance of AlTiN-Coated PM M42 High-Speed Steel

Zijun Qi iD, Yi Chen, Ji Li, Yongde Huang, Qian Wang, Qi Wei, Xiaofeng Yang iD, Qiang Liu

Materials · 2026-04-21 · 19 (8) · 1667

DOI: 10.3390/ma19081667 ↗

At a glance

Journal article in Materials, published online on 2026-04-21. Written by Zijun Qi and 7 co-authors. Institution: School of Material Science and Engineering, Nanchang Hangkong University, Nanchang 330063, China. 52 references. The full text is freely available (open access, CC BY 4.0). Funded by: Qian Wang, Chinese Academy of Sciences, 2023 Ganzhou “Jiebangguashuai” Program.

AbstractSubjectsBibliografiske oplysningerCiteRelated studies

Abstract (original language)

Preparing a highly wear-resistant AlTiN coating on a powder metallurgy (PM) M42 high-speed steel substrate is a key strategy to enhance tool performance and meet the demands of efficient machining. This study adopted a process route comprising substrate preparation, heat treatment regulation, and arc-PVD deposition of AlTiN coatings to systematically investigate the influence of sintering temperature (1130, 1160, and 1190 °C) and austenitizing time (1150 °C for 0, 15, 60, and 120 min) on the microstructure and mechanical properties of the substrate, as well as on the tribological performance of the AlTiN coatings. The results indicate that elevating the sintering temperature promotes densification of the matrix, with Vickers hardness increasing from 366 HV to 462 HV and bending strength (σ) increasing from 1064 MPa to 1310 MPa. The predominant carbide phases identified are MC, M2C, and M6C. During austenitizing, microstructural changes consistent with a progressive transformation from M2C to MC and M6C carbides were indicated by SEM and XRD analyses. Precipitation strengthening was most evident after 60 min, with hardness reaching 868 HV. In contrast, bending strength (σ) exhibited a progressive decline with increasing austenitizing time, decreasing from 1310 MPa to 1015 MPa after 120 min, illustrating a clear trade-off between hardness and toughness. The wear behavior of the coating is governed synergistically by substrate hardness, bending strength (σ), coating–substrate interfacial adhesion strength (LC), and carbide phase transformation. Elevated substrate hardness enhances anti-wear performance; bending strength influences crack propagation and spallation tendency; and LC determines the efficiency of interfacial load transfer. The carbide phase evolution appears to modulate the coating’s wear behavior by regulating both the microstructure and mechanical properties of the substrate. Among the six sample conditions evaluated, the A3 sample (sintered at 1190 °C and austenitized for 120 min) exhibited the lowest wear rate (2.38 × 10−6 mm3·N−1·m−1), demonstrating superior wear resistance. These findings provide a reference for process optimization and rational design of M42/AlTiN composite coating systems.

Subjects

Author keywords

AlTiN coatingM42 high-speed steelcarbide phase evolutionfriction and wearmechanical propertieswear rate

Authors and institutions

  • School of Material Science and Engineering, Nanchang Hangkong University, Nanchang 330063, China.
  • University of Science and Technology of China, Hefei 230026, China.
  • Key Laboratory of Rare Earths, Ganjiang Innovation Academy, Chinese Academy of Sciences, Ganzhou 341119, China.
  • School of Intelligent Manufacturing (Aerospace Engineering), Taizhou University, Taizhou 318000, China.

ORCID profiles: Zijun Qi, Xiaofeng Yang

Funding

  • Qian Wang
  • Chinese Academy of Sciences
  • 2023 Ganzhou “Jiebangguashuai” Program
  • Jiangxi Double Thousand Plan

Cite

APA

Qi, Z., Chen, Y., Li, J., Huang, Y., Wang, Q., Wei, Q., Yang, X., & Liu, Q. (2026). Influence of Sintering and Heat Treatment on the Microstructure, Mechanical Properties, and Tribological Performance of AlTiN-Coated PM M42 High-Speed Steel. Materials, 19(8), 1667. https://doi.org/10.3390/ma19081667

Vancouver

Qi Z, Chen Y, Li J, Huang Y, Wang Q, Wei Q, et al. Influence of Sintering and Heat Treatment on the Microstructure, Mechanical Properties, and Tribological Performance of AlTiN-Coated PM M42 High-Speed Steel. Materials. 2026;19(8):1667. doi:10.3390/ma19081667

BibTeX
@article{Qi2026,
  author = {Qi, Zijun and Chen, Yi and Li, Ji and Huang, Yongde and Wang, Qian and Wei, Qi and Yang, Xiaofeng and Liu, Qiang},
  title = {Influence of Sintering and Heat Treatment on the Microstructure, Mechanical Properties, and Tribological Performance of AlTiN-Coated PM M42 High-Speed Steel},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {8},
  pages = {1667},
  doi = {10.3390/ma19081667}
}
Start for free →