EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Influence of Heat Treatment on Microstructure and Tribological Behavior of Conventional Maraging Steel W720 WMR

Jana Escherova, Michal Krbata, Daniel Križan, Patrik Klučiar, Marcel Kohutiar, Igor Barényi, Tomáš Hmeľár, Andrej Opálek, Henrieta Chochlíková, Mariana Kuffová

Journal of Manufacturing and Materials Processing · 05.11.2026 · 10 (11) · 486

DOI: 10.3390/jmmp10110486 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Manufacturing and Materials Processing, online erschienen am 05.11.2026. Verfasst von Jana Escherova und 9 weiteren Autor:innen. Die Arbeit nennt 31 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Slovak Research and Development Agency.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study evaluates the effect of different precipitation-hardening regimes on the microstructure, hardness, and tribological behaviour of W720 maraging steel. Experimental specimens were aged at temperatures ranging from 460 to 490 °C for 3–16 h following solution annealing. Tribological tests were performed using the Ball-on-Flat method under dry sliding conditions against a G40 steel ball. The worn surfaces were analysed using LSCM, SEM, and EDS. Aging increased the hardness from 323 HV1 to 580–606 HV1 and reduced the coefficient of friction from approximately 0.75 to 0.63–0.71. The lowest nominal specimen wear volume was measured for the as-received, solution-annealed W720 condition (0.011 mm3), followed by HT490_6 (0.012 mm3); these values were compared descriptively without inferential statistical testing. However, the reference specimen produced a narrow, locally deepest wear track and caused the highest wear of the counter-body. The highest wear volume of the specimen was recorded for HT480_3 (0.027 mm3), while HT460_8x2 combined the highest hardness and the lowest coefficient of friction with a high wear volume. The dominant wear mechanism was a combination of abrasive grooving, adhesive damage, and tribo-oxidation. The results demonstrated that the tribological resistance of W720 is not governed by hardness alone, but rather by the interplay between microstructure, wear-track geometry, wear-product morphology, and the distribution of wear between the specimen and the counter-body.

Förderung

  • Slovak Research and Development Agency

Zitieren

APA

Escherova, J., Krbata, M., Križan, D., Klučiar, P., Kohutiar, M., Barényi, I., Hmeľár, T., Opálek, A., Chochlíková, H., & Kuffová, M. (2026). Influence of Heat Treatment on Microstructure and Tribological Behavior of Conventional Maraging Steel W720 WMR. Journal of Manufacturing and Materials Processing, 10(11), 486. https://doi.org/10.3390/jmmp10110486

Vancouver

Escherova J, Krbata M, Križan D, Klučiar P, Kohutiar M, Barényi I, et al. Influence of Heat Treatment on Microstructure and Tribological Behavior of Conventional Maraging Steel W720 WMR. Journal of Manufacturing and Materials Processing. 2026;10(11):486. doi:10.3390/jmmp10110486

BibTeX
@article{Escherova2026,
  author = {Escherova, Jana and Krbata, Michal and Križan, Daniel and Klučiar, Patrik and Kohutiar, Marcel and Barényi, Igor and Hmeľár, Tomáš and Opálek, Andrej and Chochlíková, Henrieta and Kuffová, Mariana},
  title = {Influence of Heat Treatment on Microstructure and Tribological Behavior of Conventional Maraging Steel W720 WMR},
  journal = {Journal of Manufacturing and Materials Processing},
  year = {2026},
  volume = {10},
  number = {11},
  pages = {486},
  doi = {10.3390/jmmp10110486}
}
Kostenlos starten →