EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Influence of Base Plate Preheating on Laser Powder Bed Fusion–Processed EN AW-7075 Aluminium Alloy

Nejc Velikajne iD, Jožef Medved iD, Črtomir Donik iD, Irena Paulin

Materials · 03.03.2026 · 19 (5) · 970

DOI: 10.3390/ma19050970 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 03.03.2026. Verfasst von Nejc Velikajne und 3 weiteren Autor:innen. Beteiligte Einrichtung: Institute of Metals and Technology, Lepi pot 11, SI-1000 Ljubljana, Slovenia. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 42 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: ARIS - Slovenian Research and Innovation Agency, Slovenian Research and Innovation Agency.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The influence of base plate temperature (25, 100, 200, and 400 °C) on the laser powder bed fusion processing of EN AW 7075 was systematically investigated using microstructural characterisation (LM, SEM, EBSD, GROD), chemical analysis, hardness testing, and thermal simulations across a broad range of process parameters. Moderate preheating at 100 °C and 200 °C showed no significant reduction in crack density or changes in grain morphology compared to processing without preheating. At the highest studied temperature—400 °C—a transition to columnar crack networks was observed, accompanied by modified grain orientation, pronounced stress relaxation, and reduced hardness. Independent of preheating temperature, consistent evaporation of Zn (~1 wt.%) and Mg (~0.3 wt.%) occurred during processing. Thermal simulations qualitatively supported the experimental observations, indicating increased thermal retention and displacement with increasing preheating temperature. The results demonstrate that base plate preheating alone is insufficient to suppress hot cracking in EN AW 7075 and may promote alternative crack-growth mechanisms at elevated temperatures, highlighting the need for alternative alloy or process design strategies.

Schlagwörter

Stichwörter der Autor:innen

EN AW 7075base plate preheatcrackslaser powder bed fusion (LPBF)solidification rate

Autor:innen und Institutionen

  • Institute of Metals and Technology, Lepi pot 11, SI-1000 Ljubljana, Slovenia.
  • Faculty of Natural Sciences and Engineering, University of Ljubljana, Aškerčeva cesta 12, SI-1000 Ljubljana, Slovenia.

ORCID-Profile: Nejc Velikajne, Jožef Medved, Črtomir Donik

Förderung

  • ARIS - Slovenian Research and Innovation Agency
  • Slovenian Research and Innovation Agency

Zitieren

APA

Velikajne, N., Medved, J., Donik, Č., & Paulin, I. (2026). Influence of Base Plate Preheating on Laser Powder Bed Fusion–Processed EN AW-7075 Aluminium Alloy. Materials, 19(5), 970. https://doi.org/10.3390/ma19050970

Vancouver

Velikajne N, Medved J, Donik Č, Paulin I. Influence of Base Plate Preheating on Laser Powder Bed Fusion–Processed EN AW-7075 Aluminium Alloy. Materials. 2026;19(5):970. doi:10.3390/ma19050970

BibTeX
@article{Velikajne2026,
  author = {Velikajne, Nejc and Medved, Jožef and Donik, Črtomir and Paulin, Irena},
  title = {Influence of Base Plate Preheating on Laser Powder Bed Fusion–Processed EN AW-7075 Aluminium Alloy},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {5},
  pages = {970},
  doi = {10.3390/ma19050970}
}
Kostenlos starten →