Stress–Strain and Dimension Evolution of Wind Turbine Bearing Ring with Non-Standard Section During Hot Bulging Process
Materials · 28.02.2026 · 19 (5) · 938
DOI: 10.3390/ma19050938 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 28.02.2026. Verfasst von Ruijie Gu und 7 weiteren Autor:innen. Beteiligte Einrichtung: School of Mechatronics Engineering, Henan University of Science and Technology, Luoyang 471003, China. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 40 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Key R&D Special Project of Henan Province, Henan Provincial Science and Technology Research Project, Key Scientific Research Projects of Colleges and Universities in Henan Province.
Abstract (Originalsprache)
As wind turbines trend toward larger sizes, higher rotational speeds, and extended service lives, higher demands are emerging for the dimensional accuracy, mechanical properties, and service reliability of the main shaft bearings. The hot bulging process is a critical process in bearing ring manufacturing. The stress–strain and dimensional evolution during the hot bulging process are crucial for the fatigue life and dimensional accuracy of rings with non-circular cross-sections. Therefore, based on the residual stress field from rolling as an initial condition, this paper established a coupled finite element model for the entire rolling-to-bulging process of GCr15SiMn bearing steel rings and verified the accuracy of the model. A stepwise rotation hot bulging process was innovatively designed. The stresses, strains, and deformation rates of the rings were thoroughly evaluated at different steps of the bulging process. Additionally, the effect of the bulge amount on the stress–strain uniformity and dimensional accuracy of the fabricated rings was also evaluated. Results indicate that based on the stepwise rotation hot bulging process conducted at 870–930 °C, when the first-step bulging amount is 1.50 mm, the secondary and third-step amounts are both 0.50 mm, and the bulging speed is 1.00 mm/s, while the roundness error of ring #3 stabilizes within 0.28–0.35 mm. The standard deviation of the axial equivalent strain was decreased by 92%, and the stress peak was also decreased by 39%. Above all, the stepwise rotation hot bulging process is an effective approach to improve the distribution uniformity of the stress–strain and the dimensional consistency of the bearing rings. This paper provides theoretical foundations and process guidance for the precision forming of large wind turbine bearing rings with non-standard sections.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- School of Mechatronics Engineering, Henan University of Science and Technology, Luoyang 471003, China.
- State Key Laboratory of Intelligent Mining Heavy Equipment, Luoyang 471003, China.
- LYC Bearing Group Corporation, Luoyang 471000, China.
- School of Intelligent Manufacturing and Electrical Engineering, Nanyang Normal University, Nanyang 473001, China.
Förderung
- Key R&D Special Project of Henan Province
- Henan Provincial Science and Technology Research Project
- Key Scientific Research Projects of Colleges and Universities in Henan Province
- Henan Science and Technology Projects
Zitieren
APA
Gu, R., Fu, Y., Shang, Z., Zhang, Z., Lan, S., Wang, T., Wang, Q., & Chen, L. (2026). Stress–Strain and Dimension Evolution of Wind Turbine Bearing Ring with Non-Standard Section During Hot Bulging Process. Materials, 19(5), 938. https://doi.org/10.3390/ma19050938
Vancouver
Gu R, Fu Y, Shang Z, Zhang Z, Lan S, Wang T, et al. Stress–Strain and Dimension Evolution of Wind Turbine Bearing Ring with Non-Standard Section During Hot Bulging Process. Materials. 2026;19(5):938. doi:10.3390/ma19050938
BibTeX
@article{Gu2026,
author = {Gu, Ruijie and Fu, Yutong and Shang, Ziyang and Zhang, Zhuangya and Lan, Shan and Wang, Tongxun and Wang, Qiang and Chen, Liaoyuan},
title = {Stress–Strain and Dimension Evolution of Wind Turbine Bearing Ring with Non-Standard Section During Hot Bulging Process},
journal = {Materials},
year = {2026},
volume = {19},
number = {5},
pages = {938},
doi = {10.3390/ma19050938}
}
EUVIMED