Microstructure improvement of alloys for turbine hot section components
Journal of Achievements in Materials and Manufacturing Engineering · 01.11.2025
DOI: 10.5604/01.3001.0055.7189 ↗Kurz gefasst
Fachartikel in der Zeitschrift Journal of Achievements in Materials and Manufacturing Engineering, erschienen am 01.11.2025. Verfasst von O. Glotka und 2 weiteren Autor:innen. Die Arbeit nennt 21 Literaturangaben.
Abstract (Originalsprache)
The purpose is to establish dependencies between chemical and phase composition in the Ni-Al-Cr-Co-W-Mo-Ti-Nb-Ce-Zr-B-La system; obtain dependencies between the mismatch of crystal lattices of the strengthening phase and matrix; obtain dependencies between phase composition and mechanical properties to increase the service life of hot-tract parts.The methodology for obtaining the dependencies involved simulating the thermodynamic processes of phase formation, where the elements were changed step by step using the CALPHAD thermodynamic modelling method. Predictive calculations were performed based on the initial chemical composition of the VZhL-12 alloy, which determined the most probable phases and their corresponding chemical compositions. The phase composition was experimentally determined using a REM-106I scanning electron microscope with an energy-dispersive X-ray spectral microanalysis system. The method was employed to investigate the morphology and chemical composition of the precipitated phases within the alloy structure.The influence of individual alloying elements on phase stability has been established: aluminium promotes the formation of the γ′-phase, reaching its content of up to 89% at 7.6% Al, but when in excess, it causes the formation of brittle TСР phases, which impair ductility; titanium also increases the content of the γ′-phase, but when the content is above 6.4%, it leads to the formation of lamellar TСP phases (for example, the η-phase), which negatively affect the mechanical properties; cobalt and chromium increase their concentration in the strengthening phase, promoting its thermal stability. Molybdenum and tungsten do not directly participate in the formation of the γ′-phase but increase its heat resistance. The effect of temperature on the lattice parameters of the γ and γ′-phases is shown. The minimum mismatch of the lattice parameters (-0.4%) is observed at 700-800C, corresponding to optimal values of strength, ductility, and creep resistance. Experimental testing on the industrial single-crystal alloy VZhL-12 yielded good agreement between the calculated and actual data.The established patterns of alloying, phase transformations, and thermomechanical properties can serve as the basis for creating new generations of materials capable of operating under extremely high temperatures and loads. However, the disadvantages of this method include sensitivity to the initial data, the ability to analyse materials only in a stable state, and the reliability of thermodynamic databases (which have recently improved significantly). Future studies are planned to study the behaviour of secondary phases and the influence of rare earth elements in the system.The obtained relationships between alloying, phase transformations and thermomechanical properties can be used to create new generations of materials. They enable the determination of properties of new alloys without testing, significantly reducing research costs. The work will also be beneficial in refining the existing chemical compositions of alloys.The work is intended for researchers and engineers in the field of high-temperature materials (superalloys).
Zitieren
APA
Glotka, O., Kononov, V., & Fasol, Y. (2025). Microstructure improvement of alloys for turbine hot section components. Journal of Achievements in Materials and Manufacturing Engineering. https://doi.org/10.5604/01.3001.0055.7189
Vancouver
Glotka O, Kononov V, Fasol Y. Microstructure improvement of alloys for turbine hot section components. Journal of Achievements in Materials and Manufacturing Engineering. 2025. doi:10.5604/01.3001.0055.7189
BibTeX
@article{Glotka2025,
author = {Glotka, O. and Kononov, V. and Fasol, Y.},
title = {Microstructure improvement of alloys for turbine hot section components},
journal = {Journal of Achievements in Materials and Manufacturing Engineering},
year = {2025},
doi = {10.5604/01.3001.0055.7189}
}
EUVIMED