EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effects of Annealing Temperature on the Microstructure and Mechanical Properties of Asymmetrically Rolled Ultra-Thin Ti-6Al-4V

Tao Sun iD, Tan Liu iD, Mingpei Jiang, Peng Huang, Xianli Yang, Xianlei Hu

Materials · 02.12.2025 · 18 (23) · 5436

DOI: 10.3390/ma18235436 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 02.12.2025. Verfasst von Tao Sun und 5 weiteren Autor:innen. Beteiligte Einrichtung: State Key Laboratory of Digital Steel, Northeastern University, Shenyang 110819, China. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 50 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In this study, the asymmetrical rolling technique was employed to fabricate 75 μm-thick Ti-6Al-4V ultra-thin strips from the initial 0.45 mm sheet without intermediate annealing, aiming for applications in fuel cell bipolar plates. The rolled strips exhibited good surface quality without cracking. In order to enhance both the mechanical response and the shaping capability of Ti-6Al-4V strips produced by asymmetric rolling, the material was subjected to annealing at various temperatures, and the resulting changes in microstructural features and mechanical performance were systematically examined. The findings indicated that the cold-rolled Ti-6Al-4V exhibited a microstructure primarily composed of subgrains with an average size of approximately 0.41 μm, a feature that contributed to improved corrosion resistance and enhanced ductility after annealing. When the alloy was subjected to heat treatment within the range of 650–800 °C, it was observed that annealing temperatures below 700 °C favored microstructural changes governed predominantly by recovery processes and the onset of recrystallization. At 700 °C, the grains became equiaxed and uniformly distributed, and the dislocation density significantly decreased. The tensile strength reached 887 MPa, while the elongation increased to 13.7%, achieving an excellent strength-ductility balance. Once the annealing temperature rose above 700 °C, noticeable grain growth took place, accompanied by a more pronounced grain-size gradient and a renewed increase in dislocation density. Meanwhile, the dimples observed on the fracture surface became finer, collectively contributing to a decline in tensile elongation. The Ti-6Al-4V ultra-thin strip annealed at 700 °C was used for bipolar plate stamping, producing fine micro-channels with an aspect ratio of 0.43. Finally, TiN coating was applied to the surface, which significantly improved the corrosion resistance and reduced the interfacial contact resistance (ICR), meeting the performance requirements for bipolar plates.

Schlagwörter

Stichwörter der Autor:innen

TiN coatingannealingasymmetrical rollingbipolar plateultra-thin strip

Autor:innen und Institutionen

  • State Key Laboratory of Digital Steel, Northeastern University, Shenyang 110819, China.
  • School of Material Science and Engineering, Northeastern University, Shenyang 110819, China.
  • Suzhou Laboratory, Suzhou 215125, China.

ORCID-Profile: Tao Sun, Tan Liu

Zitieren

APA

Sun, T., Liu, T., Jiang, M., Huang, P., Yang, X., & Hu, X. (2025). Effects of Annealing Temperature on the Microstructure and Mechanical Properties of Asymmetrically Rolled Ultra-Thin Ti-6Al-4V. Materials, 18(23), 5436. https://doi.org/10.3390/ma18235436

Vancouver

Sun T, Liu T, Jiang M, Huang P, Yang X, Hu X. Effects of Annealing Temperature on the Microstructure and Mechanical Properties of Asymmetrically Rolled Ultra-Thin Ti-6Al-4V. Materials. 2025;18(23):5436. doi:10.3390/ma18235436

BibTeX
@article{Sun2025,
  author = {Sun, Tao and Liu, Tan and Jiang, Mingpei and Huang, Peng and Yang, Xianli and Hu, Xianlei},
  title = {Effects of Annealing Temperature on the Microstructure and Mechanical Properties of Asymmetrically Rolled Ultra-Thin Ti-6Al-4V},
  journal = {Materials},
  year = {2025},
  volume = {18},
  number = {23},
  pages = {5436},
  doi = {10.3390/ma18235436}
}
Kostenlos starten →