EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Water Sorption and Water Solubility of Digitally Fabricated Denture Base Materials

Josip Vuksic, Ana Pilipovic iD, Tina Poklepovic Pericic, Josip Kranjcic

Materials · 27.11.2025 · 18 (23) · 5343

DOI: 10.3390/ma18235343 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 27.11.2025. Verfasst von Josip Vuksic und 3 weiteren Autor:innen. Beteiligte Einrichtung: University of Zagreb, School of Dental Medicine, Gunduliceva 5, 10000 Zagreb, Croatia. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 44 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Project "Advanced dental materials: characterization, clinical applications and emerging challenges", co-financed by the National Recovery and Resilience Plan…, Advanced dental materials: characterization, clinical applications and emerging challenges, National Recovery and Resilience Plan.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

(1)

Background

Digitally fabricated denture base materials are increasingly used in everyday clinical practice, but scientific data on their properties is limited, especially regarding water sorption and water solubility. Water absorbed in denture base material penetrates between the polymer chains, acts as a plasticiser, and negatively affects mechanical properties. Residual monomers and other chemicals not chemically bonded in the polymer matrix can dissolve in water and may cause biological consequences such as irritation and inflammation of the oral mucosa or even allergic reactions. This can also have a deteriorating effect on the materials. Therefore, the aim of this study was to investigate the water sorption and water solubility of digitally fabricated denture base materials. (2)

Methods

Six denture base materials were used in this investigation: three subtractively manufactured materials, two additively manufactured materials, and one heat-cured poly(methyl methacrylate) material as a control group. The investigation was carried out according to ISO 20795-1:2013. (3)

Results

Water sorption for the control group was 28.02 µg/mm3, while all digitally fabricated denture base materials showed statistically significantly lower values, ranging between 20.42 and 23.54 µg/mm3, with a statistical difference observed within the subtractively manufactured group. All materials had water sorption values below the upper limit of 32 µg/mm3 specified in ISO 20795-1:2013. Water solubility for subtractively manufactured materials ranged between 0.04 and 0.40 µg/mm3, with values both higher and lower than the control group, but with no statistical difference. Water solubility for additively manufactured materials was 3.01 and 3.22 µg/mm3, which was statistically significantly higher than the control group, and these results exceeded the upper limit of 1.6 µg/mm3 specified in ISO 20795-1:2013. (4)

Conclusions

Digitally fabricated denture base materials showed improved water sorption compared to the heat-cured material, while water solubility for subtractively manufactured materials was similar to the heat-cured material and poorer for additively manufactured denture base materials, with results that did not meet the minimum requirements set by ISO 20795-1:2013.

Schlagwörter

Stichwörter der Autor:innen

CAD-CAMdenture basewater solubilitywater sorption

Autor:innen und Institutionen

  • University of Zagreb, School of Dental Medicine, Gunduliceva 5, 10000 Zagreb, Croatia.
  • University Hospital Dubrava, Av. Gojka Šuška 6, 10000 Zagreb, Croatia.
  • University of Zagreb, Faculty of Mechanical Engineering and Naval Architecture, Ivana Lučića 5, 10000 Zagreb, Croatia.
  • Department of Prosthodontics, Study of Dental Medicine, University of Split, School of Medicine, Šoltanska 2, 21000 Split, Croatia.

ORCID-Profile: Ana Pilipovic

Förderung

  • Project "Advanced dental materials: characterization, clinical applications and emerging challenges", co-financed by the National Recovery and Resilience Plan…
  • Advanced dental materials: characterization, clinical applications and emerging challenges
  • National Recovery and Resilience Plan

Zitieren

APA

Vuksic, J., Pilipovic, A., Poklepovic Pericic, T., & Kranjcic, J. (2025). Water Sorption and Water Solubility of Digitally Fabricated Denture Base Materials. Materials, 18(23), 5343. https://doi.org/10.3390/ma18235343

Vancouver

Vuksic J, Pilipovic A, Poklepovic Pericic T, Kranjcic J. Water Sorption and Water Solubility of Digitally Fabricated Denture Base Materials. Materials. 2025;18(23):5343. doi:10.3390/ma18235343

BibTeX
@article{Vuksic2025,
  author = {Vuksic, Josip and Pilipovic, Ana and Poklepovic Pericic, Tina and Kranjcic, Josip},
  title = {Water Sorption and Water Solubility of Digitally Fabricated Denture Base Materials},
  journal = {Materials},
  year = {2025},
  volume = {18},
  number = {23},
  pages = {5343},
  doi = {10.3390/ma18235343}
}
Kostenlos starten →