EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Formability and Electromagnetic Performance Comparison of Fe-P-Based SMC and Fe-5.0 wt.%Si Powders

Seongsu Kang iD, Seonbong Lee

Materials · 21.09.2025 · 18 (18) · 4405

DOI: 10.3390/ma18184405 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 21.09.2025. Verfasst von Seongsu Kang und 1 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, Keimyung University, Daegu 42601, Republic of Korea. Die Arbeit wurde bisher 7-mal zitiert (Crossref) und nennt 67 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Korea Government (MOTIE), Korea Institute for Advancement of Technology (KIAT).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study investigates the comparative applicability of Somaloy 700HR 5P and Fe-5.0 wt.%Si powders for axial flux permanent magnet (AFPM) motor cores in low-speed electric vehicles. Optimal forming conditions were derived through Taguchi-based simulations, considering corner radius, forming temperature, and forming speed, followed by prototype fabrication and validation. Simulation and SEM-EDS analyses confirmed consistent density distribution trends, and XRD verified phase stability during forming. While Fe-5.0 wt.%Si exhibited ~10% ± 2 superior electromagnetic performance in the powder state, its motor dynamo performance decreased by 19–25% (n = 1) compared to Somaloy 700HR 5P. This discrepancy was attributed to its ~4% lower target density (7.19 ± 0.02 g/cm3 vs. 7.51 ± 0.01 g/cm3, n = 3), assembly-induced mechanical losses, and non-uniform insulation layer caused by residual H3PO4 and Mo segregation. Somaloy 700HR 5P, despite a higher relative density variation (0.084 ± 0.002 g/cm3 vs. 0.063 ± 0.003 g/cm3 for Fe-5.0 wt.%Si), achieved an average density close to 7.5 g/cm3 and delivered more stable motor performance. Overall, Somaloy 700HR 5P was identified as a more suitable candidate for AFPM motor cores in low-speed EV applications, balancing formability and electromagnetic performance.

Schlagwörter

Stichwörter der Autor:innen

microstructuremorphologymotorpowder metallurgy (PM)soft magnetic composites (SMCs)

Autor:innen und Institutionen

  • Department of Mechanical Engineering, Keimyung University, Daegu 42601, Republic of Korea.
  • Department of Automotive Engineering, Keimyung University, Daegu 42601, Republic of Korea.

ORCID-Profile: Seongsu Kang

Förderung

  • Korea Government (MOTIE)
  • Korea Institute for Advancement of Technology (KIAT)

Zitieren

APA

Kang, S., & Lee, S. (2025). Formability and Electromagnetic Performance Comparison of Fe-P-Based SMC and Fe-5.0 wt.%Si Powders. Materials, 18(18), 4405. https://doi.org/10.3390/ma18184405

Vancouver

Kang S, Lee S. Formability and Electromagnetic Performance Comparison of Fe-P-Based SMC and Fe-5.0 wt.%Si Powders. Materials. 2025;18(18):4405. doi:10.3390/ma18184405

BibTeX
@article{Kang2025,
  author = {Kang, Seongsu and Lee, Seonbong},
  title = {Formability and Electromagnetic Performance Comparison of Fe-P-Based SMC and Fe-5.0 wt.%Si Powders},
  journal = {Materials},
  year = {2025},
  volume = {18},
  number = {18},
  pages = {4405},
  doi = {10.3390/ma18184405}
}
Kostenlos starten →